Nissan X-Trail 32. Manual — part 1325
GW-18
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
b.
Tie both ends of the piano wire (B) to the wire grip (A), etc..
c.
Remove adhesive by using piano wire alongside of windshield
glass and body panel.
CAUTION:
• Never press piano wire excessively against edge of glass.
• Remove adhesive, 2 workers are required by all means.
19. Use rubber suction cups or suction lifter (A), etc. to remove
windshield glass from the vehicle.
CAUTION:
Due to weight of windshield glass, 2 workers are required
by all means.
Reuse Windshield Glass
CAUTION:
• Never use a windshield cutter if the windshield glass is reused. (It may scratch the glass surface)
• Never damage windshield glass and body panel.
1.
Remove all assist grips.
a.
Disengage assist grip cap fixing pawl using a remover tool (A),
and then slide assist grip cap and remove it according to numer-
ical order 1
→
2 indicated by the arrows as shown in the figure.
b.
Disengage assist grip fixing metal clips, and then remove assist grip.
2.
Remove center pillar upper garnish (LH and RH). Refer to
INT-28, "CENTER PILLAR UPPER GARNISH :
.
3.
Remove front pillar garnish (LH and RH). Refer to
INT-23, "FRONT PILLAR GARNISH : Removal and
.
JMKIA9832ZZ
JMKIB2163ZZ
JMKIA1138ZZ
: Pawl
JMJIA8937ZZ
WINDSHIELD GLASS
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
4.
Remove light & rain sensor cover. Refer to
WW-109, "Removal and Installation"
5.
Remove front camera unit. Refer to
DAS-149, "Removal and Installation"
6.
Remove map lamp assembly. Refer to
INL-76, "MAP LAMP : Removal and Installation"
.
7.
Remove sun visor assembly (LH and RH).
a.
Disengage sun visor cover fixing pawls using a remover tool (A),
and then remove sun visor cover (LH and RH).
b.
Remove sun visor assembly fixing screws, and then disconnect vanity mirror lamp harness connector.
(With vanity mirror lamp)
c.
Remove sun visor assembly (LH and RH).
8.
Remove sun visor holder (LH and RH) using a remover tool (A)
according to numerical order 1
→
2 indicated by the arrows as
shown in the figure.
CAUTION:
Use a remover tool wrapped in tape.
9.
Disengage dual lock fasteners
between headlining assembly
and roof panel. (With sunroof)
CAUTION:
Never bend headlining when removing.
10. Remove front portion of headlining assembly from roof panel.
CAUTION:
To prevent damage of the headlining assembly, hold it by
using a rope (A) or belt.
11. Remove roof side molding (LH and RH). Refer to
EXT-46, "Removal and Installation"
12. Remove cowl top cover. Refer to
EXT-25, "Removal and Installation"
.
: Pawl
JMJIA4399ZZ
JMJIA9251ZZ
: Vehicle front
JMJIA9639ZZ
JMKIB2588ZZ
GW-20
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
13. Apply protective tape (A) on roof panel and body side outer
panel around windshield glass to protect painted surface from
damage.
14. Apply matching marks to windshield glass, roof panel and both
side of body side outer panel.
CAUTION:
To prevent the gap when install windshield glass put on
matching marks by all means.
15. Remove windshield glass molding
.
CAUTION:
• Be careful not to cut hands by a cutter knife (A).
• Never scratch body panel by a cutter knife.
• Remove windshield glass molding left on vehicle using a pliers etc..
NOTE:
Use a cutter knife along the windshield glass
as shown in the figure, cut the bottom of windshield glass
molding.
16. Apply protective standish cover (A) on instrument panel to pro-
tect it from damage.
JMKIB1944ZZ
JMKIB1945ZZ
JMKIB3178ZZ
JMKIB1267ZZ
WINDSHIELD GLASS
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
17. Remove adhesive using a piano wire.
a.
Pass the piano wire (B) from passenger room to bonded area of
glass using a wire pierce (A).
CAUTION:
• Never use plane surface of wire pierce tip vertically.
• Never press piano wire excessively against edge of glass.
• Never damage surrounding parts.
b.
Tie both ends of the piano wire (B) to the wire grip (A), etc..
c.
Remove adhesive by using piano wire alongside of windshield
glass and body panel.
CAUTION:
• Never press piano wire excessively against edge of glass.
• Remove adhesive, 2 workers are required by all means.
18. Use rubber suction cups or suction lifter (A), etc. to remove
windshield glass from the vehicle.
CAUTION:
Due to weight of windshield glass, 2 workers are required
by all means.
INSTALLATION
Replacement Windshield Glass
JMKIB1452ZZ
JMKIA9832ZZ
JMKIB2163ZZ
JMKIA1138ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст