Nissan X-Trail 32. Manual — part 2119
TM-434
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
WATER HOSE
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Remove battery tray. Refer to
PG-148, "EXCEPT FOR R9M : Removal and Installation"
2.
Remove engine under cover. Refer to
EXT-40, "ENGINE UNDER COVER : Removal and Installation"
3.
Remove CVT fluid charging pipe. Refer to
4.
Remove splash side cover LH. Refer to
EXT-35, "FENDER PROTECTOR : Exploded View"
5.
Remove water hose A, B, C, and heater thermostat.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse hose clamps.
• Never reuse hose clip
• Securely install the water hose clip to the bracket hole of charging pipe.
• Refer to the following when installing water hoses.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
QR25DE : Inspection
INFOID:0000000010622628
INSPECTION AFTER REMOVAL
Hhose
Installation side
tube
Direction of paint
mark
Hose insertion depth
(L)
Water hose A
Water outlet
Upward
End reaches the end
of tube.
CVT oil warmer
Frontward
End reaches the 2-
stage bulge.
Water hose B
CVT oil warmer
Frontward
Heater thermostat
Align with the mark
on the heater ther-
mostat
Water hose C
Heater thermostat
Align with the mark
on the heater ther-
mostat
End reaches the ex-
pansion part.
Water outlet
Upward
End reaches the end
of tube.
Hose
Installation side tube
Hose clamp
Direction of tab
Clamping position (A)
Water hose A
Water outlet
Upward
5 – 7 mm (0.20 – 0.28
in) from hose end
CVT oil warmer
Leftward
Water hose B
CVT oil warmer
Leftward
5 – 9 mm (0.20 – 0.35
in) from hose end
Heater thermostat
Align with the
mark on the
hose
Water hose C
Heater thermostat
Align with the
mark on the
hose
Water outlet
Upward and
45
°
forward
JSDIA2459ZZ
JSDIA2424ZZ
WATER HOSE
TM-435
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Heater Thermostat
1.
Fully immerse the heater thermostat
in a container (A) filled
with water. Continue heating the water while stirring.
2.
Continue heating the heater thermostat for 5 minutes or more
after bringing the water to a boil.
3.
Quickly take the heater thermostat out of the hot water, measure the heater thermostat within 10 seconds.
-
Place dial indicator (A) on the pellet
and measure the elonga-
tion from the initial state.
4.
If out of standard, replace heater thermostat.
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of engine coolant.
JSDIA3661ZZ
Standard
: Refer to
.
JSDIA3662ZZ
TM-436
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CVT FLUID COOLER SYSTEM
CVT FLUID COOLER SYSTEM
MR20DD
MR20DD : Exploded View
INFOID:0000000010622629
Transaxle side
Vehicle side
JSDIA5320GB
Transaxle assembly
Copper washer
Fluid cooler tube A
Fluid cooler tube B
Hose clamp
Fluid cooler hose A
CVT oil warmer
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA6022GB
CVT FLUID COOLER SYSTEM
TM-437
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
MR20DD : Removal and Installation
INFOID:0000000010622630
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Remove front bumper. Refer to
EXT-15, "Removal and Installation"
2.
Pull out fluid cooler hose C
and fluid cooler hose E
from
fluid cooler tube assembly.
3.
Remove the mounting bolts (
) of fluid cooler tube assembly
.
4.
Pull out fluid cooler hose F
and fluid cooler hose B
from
fluid cooler tube assembly.
5.
Remove CVT fluid cooler mounting bolts
and mounting nuts
and take out the CVT fluid cooler.
CAUTION:
Be careful not to damage the radiator fins while taking out
the CVT fluid cooler.
Bracket
Bumper reinforcement
Fluid cooler hose D
Hose clamp
Fluid cooler bracket (with tube)
CVT fluid cooler
Bracket
Fluid cooler hose C
Fluid cooler hose E
Fluid cooler tube assembly
Fluid cooler hose F
Fluid cooler hose B
Fluid cooler tube A
CVT oil warmer
Transaxle assembly
Bumper reinforcement lower
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Hose clamp
: Vehicle front
JSDIA5376ZZ
: Hose clamp
JSDIA6136ZZ
: Vehicle front
JSDIA5378ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст