Nissan X-Trail 32. Manual — part 132
BR-122
< REMOVAL AND INSTALLATION >
[RHD]
REAR DISC BRAKE
• Never damage the piston boot.
• When replacing brake pad with new one, check a brake fluid level in the reservoir tank because
brake fluid returns to reservoir tank when pressing piston in.
4.
Install the lower sliding pin bolt and tighten it to the specified
torque.
5.
Must be performed additional service when removing and installing/replacing brake pad.
When removing and installing brake pad
1.
Perform “BRAKE OPERATION”. Refer to
2.
Perform “BRAKE RELEASE”. Refer to
.
When replacing brake pad
• Refer to
6.
Depress the brake pedal several times to check that no drag feel is present for the front disc brake. Refer
to
BR-122, "BRAKE PAD : Inspection and Adjustment"
.
7.
Install tires. Refer to
WT-61, "Removal and Installation"
BRAKE PAD : Inspection and Adjustment
INFOID:0000000010838978
INSPECTION AFTER REMOVAL
• Replace the shims and shim covers if rust is excessively attached.
• Eliminate rust on the pad and the torque member. Replace them if rust is excessively attached.
INSPECTION AFTER INSTALLATION
• Check a drag of rear disc brake. If any drag is found, follow the procedure described below.
1.
Remove brake pads. Refer to
BR-120, "BRAKE PAD : Removal and Installation"
2.
Press the pistons. Refer to
BR-120, "BRAKE PAD : Removal and Installation"
3.
Install brake pads. Refer to
BR-120, "BRAKE PAD : Removal and Installation"
.
4.
Depress the brake pedal several times.
5.
Check a drag of rear disc brake again. If any drag is found, disassemble the cylinder body and replace if
necessary. Refer to
BR-125, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
.
• Burnish contact surfaces brake pads and disc rotor after refinishing or replacing brake pads, or if a soft pedal
occurs at very low mileage. Refer to
BR-83, "BRAKE PAD : Inspection and Adjustment"
.
BRAKE CALIPER ASSEMBLY
BRAKE CALIPER ASSEMBLY : Exploded View
INFOID:0000000010838979
REMOVAL
JPFIA0832ZZ
REAR DISC BRAKE
BR-123
< REMOVAL AND INSTALLATION >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
DISASSEMBLY
BRAKE CALIPER ASSEMBLY : Removal and Installation
INFOID:0000000010838980
REMOVAL
WARNING:
Since dust covering the front and rear brakes has an affect on human body, the dust must be removed
with a dust collector. Never splatter the dust with an air blow gun.
CAUTION:
Brake caliper assembly
: N·m (kg-m, ft-lb)
JSFIA2412GB
Cap
Bleeder valve
Cylinder body
Sliding pin
Bushing
Bushing
Torque member
: Apply rubber grease.
JSFIA2413GB
BR-124
< REMOVAL AND INSTALLATION >
[RHD]
REAR DISC BRAKE
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. However avoid washing brake
components with water.
• Never depress the brake pedal while removing the brake pads because the piston may pop out.
• If the brake fluid or grease adheres to the brake caliper assembly and disc rotor, quickly wipe it off.
1.
Release the parking brake.
2.
Must be performed additional service when replacing brake calipper. Refer to
.
3.
Remove tires.
4.
Fix the disc rotor using wheel nuts.
5.
Drain brake fluid. Refer to
.
6.
Remove union bolt and copper washer, and separate brake hose from brake caliper assembly. Refer to
BR-92, "REAR : Removal and Installation"
7.
Remove torque member mounting bolts, and remove brake cali-
per assembly.
CAUTION:
• Never drop brake pad and brake caliper assembly.
• Never damage the electric parking brake harness and
bracket.
8.
Remove disc rotor.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• 4WD: Refer to
RAX-18, "Removal and Installation"
.
INSTALLATION
WARNING:
Since dust covering the front and rear brakes has an affect on human body, the dust must be removed
with a dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. However avoid washing brake
components with water.
• Never depress the brake pedal while removing the brake pads because the piston may pop out.
• If the brake fluid or grease adheres to the brake caliper assembly and disc rotor, quickly wipe it off.
• Never allow foreign matter (e.g.dust) and oils other than brake fluid to enter the reservoir tank.
1.
Install disc rotor.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• 4WD: Refer to
RAX-18, "Removal and Installation"
.
2.
Install the brake caliper assembly to the steering knuckle and
tighten the torque member mounting bolts to the specified
torque.
CAUTION:
Never spill or splash any grease and moisture on the brake
caliper assembly mounting face, threads, mounting bolts
and washers. Wipe out any grease and moisture.
3.
Install brake hose and copper washers to brake caliper assem-
bly. Refer to
BR-92, "REAR : Removal and Installation"
CAUTION:
Never reuse copper washer.
4.
Must be performed additional service when removing and installing/replacing brake pad.
When removing and installing brake pad
1.
Perform “BRAKE OPERATION”. Refer to
2.
Perform “BRAKE RELEASE”. Refer to
.
When replacing brake pad
• Refer to
5.
Refill with new brake fluid and perform the air bleeding. Refer to
BR-78, "Bleeding Brake System"
.
JPFIA0835ZZ
JPFIA0835ZZ
REAR DISC BRAKE
BR-125
< REMOVAL AND INSTALLATION >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
CAUTION:
• Never reuse brake fluid.
• Never spill or splash brake fluid on the surface of disc rotor.
6.
Check a drag of rear disc brake. If any drag is found, refer to
BR-126, "BRAKE CALIPER ASSEMBLY :
7.
Install tires. Refer to
WT-61, "Removal and Installation"
8.
Perform inspection after installation. Refer to
BR-126, "BRAKE CALIPER ASSEMBLY : Inspection and
.
BRAKE CALIPER ASSEMBLY : Disassembly and Assembly
INFOID:0000000010838981
DISASSEMBLY
NOTE:
Never remove the torque member and brake pad when disassembling and assembling the cylinder body.
1.
Remove the sliding pin bolt, and remove the cylinder body from the torque member. Refer to
"BRAKE PAD : Removal and Installation"
CAUTION:
Fix the brake pad at suitable tape so that the brake pad will not drop.
2.
Remove sliding pins and sliding pin boots from torque member.
3.
Remove bushing
from sliding pin
.
4.
Remove bleeder valve and cap.
5.
Perform inspection after disassembly. Refer to
BR-126, "BRAKE CALIPER ASSEMBLY : Inspection and
.
ASSEMBLY
1.
Install bleeder valve and cap.
2.
Apply rubber grease to mating faces
between sliding pin
and bushing
, and install bushing to sliding pin.
JSFIA0496ZZ
JPFIA0836ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст