Nissan X-Trail 32. Manual — part 1302
FSU-12
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
Strut Assembly
• When installing strut assembly to the vehicle, set the mounting insulator to the direction shown in the figure.
CAUTION:
Never reuse strut mounting nut.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
• After replacing the strut, always follow the disposal procedure to discard the strut. Refer to
.
Strut Assembly and Steering Knuckle Connection
CAUTION:
Be sure to remove lubricants if lubricant has been used to separate the connection of strut assembly
and steering knuckle.
Install the steering knuckle to strut assembly as follows.
1.
Set suitable jack under steering knuckle.
2.
Align the gap
of steering knuckle to the projection part
of
strut.
3.
Tighten the mounting bolt with pushing up the steering knuckle
until contacts stopper bracket
end face, using a suitable
jack.
CAUTION:
Check the stable condition when using a jack.
Disassembly and Assembly
INFOID:0000000010822755
DISASSEMBLY
CAUTION:
Never damage strut assembly piston rod when removing components from strut assembly.
: Vehicle front
JMEIA0222ZZ
JMEIA0223ZZ
JMEIA0224ZZ
FRONT COIL SPRING AND STRUT
FSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
1.
Install strut attachment (A) (SST: ST35652000) to strut assem-
bly and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly,
wrap a shop cloth around strut to protect from damage.
2.
Using a spring compressor (A) (commercial service tool), com-
press coil spring between spring upper seat and lower seat
(strut assembly) until coil spring with a spring compressor is
free.
CAUTION:
Be sure a spring compressor is securely attached to coil
spring. Compress coil spring.
3.
Check coil spring with a spring compressor between spring upper seat and lower seat (strut assembly) is
free. And then remove piston rod lock nut while securing the piston rod tip so that piston rod does not turn.
4.
Remove mounting insulator, mounting bearing, upper rubber seat and bound bumper from strut.
5.
After removing coil spring with a spring compressor (commercial service tool), then gradually release a
spring compressor.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
6.
Remove lower rubber seat.
7.
Remove strut attachment (A) (SST: ST35652000) from strut.
8.
Perform inspection after disassembly. Refer to
.
ASSEMBLY
CAUTION:
Never damage strut assembly piston rod when installing components from strut assembly.
1.
Install strut attachment (SST: ST35652000) to strut and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly, wrap a shop cloth around strut to protect
from damage.
JPEIA0006ZZ
JPEIA0007ZZ
JPEIA0006ZZ
FSU-14
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
2.
Install lower rubber seat with its protrusion
on the lower area
aligned with the hole
on the strut.
3.
Compress coil spring using a spring compressor (commercial service tool), and install it onto strut assem-
bly.
CAUTION:
• Be sure a spring compressor is securely attached to coil spring, before compress coil spring.
• Align the lower end of coil spring
with lower rubber
seat
as shown in the figure.
• Set coil spring so that its paint marks
is aligned with
the position of 1.75 turns from the bottom end of the coil
spring.
4.
Apply soapy water to bound bumper.
CAUTION:
Never use machine oil.
5.
Set bound bumper to piston rod of strut.
6.
Install mounting bearing, mounting insulator and upper rubber seat on to spring.
CAUTION:
Never apply oils, such as grease, when installing the mounting bearing and mounting insulator.
7.
Set the mounting insulator to the direction shown in the figure, and then install the mounting insulator, the
upper rubber seat and the mounting bearing to the strut.
JSEIA0892ZZ
Dimension (A)
: 5 mm (0.20 in) or less
JSEIA0658ZZ
: Upper side
JSEIA0893ZZ
JMEIA0222ZZ
FRONT COIL SPRING AND STRUT
FSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
CAUTION:
• Align the upper end of coil spring with upper rubber seat
as shown in the figure.
8.
Secure piston rod tip so that piston rod does not turn, then tighten piston rod lock nut with specified
torque.
CAUTION:
Never reuse piston rod lock nut.
9.
Gradually release a spring compressor (A) (commercial service
tool), and remove coil spring.
CAUTION:
Loosen while making sure coil spring attachment position
does not move.
10. Remove the strut attachment (A) (SST: ST35652000) from strut
assembly.
Inspection
INFOID:0000000010822756
INSPECTION AFTER DISASSEMBLY
Check the following items, and replace the parts if necessary.
Strut
• Strut for deformation, cracks or damage
• Piston rod for damage, uneven wear or distortion
• Oil leakage
Strut Mounting Insulator and Bound Bumper
Check strut mounting insulator and bound bumper for cracks, wear or damage.
Coil Spring
Check coil spring for cracks, wear or damage.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
Dimension (A)
: 5 mm (0.20 in) or less
JSEIA0894ZZ
JPEIA0007ZZ
JPEIA0006ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст