Nissan X-Trail 32. Manual — part 46
AV-176
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U0428 STEERING ANGLE SENSOR
U0428 STEERING ANGLE SENSOR
DTC Description
INFOID:0000000010714839
POSSIBLE CAUSE
• Neutral position of steering angle sensor is not yet adjusted
• Steering angle sensor
FAIL-SAFE
• Predicted course line is not displayed
• DAA system is cancel
• BSW system is cancel
• MOD (Moving Object Detection) function is cancel
• Around view monitor with Park Assist is cancel
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC C0428 is displayed with DTC U1232, first perform the confirmation procedure (trouble diagnosis) for
DTC U1232.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn the ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “AVM” using CONSULT.
5.
Check DTC.
Is DTC U0428 detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010714840
1.
ADJUST THE NEUTRAL POSITION OF THE STEERING ANGLE SENSOR
When U0428 is detected, adjust the neutral position of the steering angle sensor.
>> Perform adjustment of the neutral position of the steering angle sensor. Refer to
.
CAUTION:
For vehicles with VDC, adjust the steering angle sensor neutral position on the ABS actuator control
unit side.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
U0428
ST ANGLE SENSOR CALIBRA-
TION
(Steering angle sensor calibration)
The neutral position adjustment of the steering angle sensor is incomplete.
AV
U1000 CAN COMM CIRCUIT
AV-177
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1000 CAN COMM CIRCUIT
NAVI CONTROL UNIT
NAVI CONTROL UNIT : DTC Description
INFOID:0000000010714841
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on board multi-
plex communication line with high data communication speed and excellent error detection ability. A modern
vehicle is equipped with many ECMs, and each control unit shares information and links with other control
units during operation (not independent). In CAN communication, 2 control units are connected with 2 commu-
nication lines (CAN H-line and CAN L-line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Refer to
LAN-41, "CAN COMMUNICATION SYSTEM : CAN Communication Signal Chart"
communication signal.
DTC DETECTION LOGIC
POSSIBLE CAUSE
CAN communication system
FAIL-SAFE
The system using the CAN communication signal from control unit which cannot communicate does not func-
tion
DTC CONFIRMATION PROCEDURE
NOTE:
• The auto ACC function allows the accessory power supply for a certain period of time even after ignition
switch OFF. For this reason, when performing diagnosis, turn the ignition switch OFF and wait for 3 minutes
with the driver's door opened.
• The operation of the vehicle during standby may cause an accessory power supply.
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn the ignition switch ON.
2.
Turn ignition switch OFF and wait for 3 minutes with the driver's door opened.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “MULTI AV” using CONSULT.
5.
Check DTC.
Is DTC U1000 detected?
YES
>> Refer to
AV-177, "NAVI CONTROL UNIT : Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
NAVI CONTROL UNIT : Diagnosis Procedure
INFOID:0000000010714842
1.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
With CONSULT
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC confirmation procedure again. Refer to
AV-177, "NAVI CONTROL UNIT : DTC Description"
.
Is DTC U1000 detected again?
YES
>> Perform the trouble diagnosis for CAN communication system. Refer to
.
NO
>> INSPECTION END
AROUND VIEW MONITOR CONTROL UNIT
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detection condition
U1000
CAN COMM CIRC
(CAN communication circuit)
When the NAVI control unit cannot communicate for 2 seconds or more.
AV-178
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U1000 CAN COMM CIRCUIT
AROUND VIEW MONITOR CONTROL UNIT : DTC Description
INFOID:0000000010714843
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on board multi-
plex communication line with high data communication speed and excellent error detection ability. A modern
vehicle is equipped with many ECMs, and each control unit shares information and links with other control
units during operation (not independent). In CAN communication, 2 control units are connected with 2 commu-
nication lines (CAN H-line and CAN L-line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Refer to
LAN-41, "CAN COMMUNICATION SYSTEM : CAN Communication Signal Chart"
for details of the
communication signal.
DTC DETECTION LOGIC
NOTE:
If “U1000” is detected, first diagnose the CAN communication system.
POSSIBLE CAUSE
CAN communication system
FAIL-SAFE
The following functions are cancel
• When communication of steering angle sensor signal is not normal
- Predicted course line is not displayed
- MOD (Moving Object Detection) function is cancel
- DAA system is cancel
- BSW system is cancel
- Around view monitor with Park Assist is cancel
• When communication of vehicle signal, wheel speed sensor signal, and shift signal is not normal
- Predicted course line is not displayed
- MOD (Moving Object Detection) function is cancel
- DAA system is cancel
- BSW system is cancel
- Around view monitor with Park Assist is cancel
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn the ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “AVM” using CONSULT.
5.
Check DTC.
Is DTC U1000 detected?
YES
>> Refer to
AV-178, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure
INFOID:0000000010714844
1.
PERFORM THE SELF-DIAGNOSIS
1.
Start the engine.
2.
Turn the LDW system ON, and then wait for 30 seconds or more.
3.
Perform “All DTC Reading” with CONSULT.
4.
Check if the “U1000” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U1000” detected as the current malfunction?
DTC
Trouble diagnosis contents
(Trouble diagnosis contents)
Detecting condition
U1000
CAN COMM CIRCUIT
(CAN communication circuit)
Around view monitor control unit is not transmitting or receiving CAN com-
munication signal for 2 seconds or more.
AV
U1000 CAN COMM CIRCUIT
AV-179
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
YES
>> Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст