Nissan X-Trail 32. Manual — part 1610
MWI-122
< DTC/CIRCUIT DIAGNOSIS >
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
DTC Description
INFOID:0000000010715006
DTC DETECTION LOGIC
POSSIBLE CAUSE
Combination meter
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Check “Self Diagnostic Result” of “METER/M&A.”
Is “CONTROL UNIT (CAN)” displayed?
YES
>> Refer to
MWI-122, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715007
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Erase the self-diagnostic results.
3.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> Replace combination meter. Refer to
MWI-151, "Removal and Installation"
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
U1010
CONTROL UNIT (CAN)
[Control unit (CAN)]
When detecting error during the initial diagnosis of the CAN controller of combination meter.
MWI
B2205 VEHICLE SPEED
MWI-123
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2205 VEHICLE SPEED
DTC Description
INFOID:0000000010715008
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Wheel sensor
• ABS actuator and electric unit (control unit)
FAIL-SAFE
Reset to zero by suspending communication.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Check “Self Diagnostic Result” of “METER/M&A.”
Is “VEHICLE SPEED” displayed?
YES
>> Refer to
MWI-123, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715009
1.
PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Perform “Self Diagnostic Result” of “ABS.”
Is DTC detected?
YES
>> Perform diagnosis procedure on the detected DTC. Refer to
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B2205
VEHICLE SPEED
(Vehicle speed)
An abnormal vehicle speed signal is input from ABS actuator and electric unit (control unit)
for 2 seconds or more
MWI-124
< DTC/CIRCUIT DIAGNOSIS >
B2267 ENGINE SPEED
B2267 ENGINE SPEED
DTC Description
INFOID:0000000010715010
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Crankshaft position sensor (POS)
• ECM
• TCM
FAIL-SAFE
Reset to zero by suspending communication.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and wait for 2 seconds or more.
2.
Check “Self Diagnostic Result” of “METER/M&A.”
Is “ENGINE SPEED” displayed?
YES
>> Refer to
MWI-124, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715011
1.
PERFORM SELF-DIAGNOSIS OF ECM
Perform “Self Diagnostic Result” of “ECM.”
Is DTC detected?
YES
>> Perform diagnosis procedure on the detected DTC. Refer to
(MR20DD),
(QR25DE), or
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B2267
ENGINE SPEED
(Engine speed)
TCM continuously transmits abnormal engine speed signals for 2 seconds or more
MWI
B2268 WATER TEMP
MWI-125
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2268 WATER TEMP
DTC Description
INFOID:0000000010715012
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Engine coolant temperature sensor
• ECM
FAIL-SAFE
• When reception time of an abnormal signal is 60 seconds or less, the last value received.
• When reception time of an abnormal signal is more than 60 seconds, reset to zero.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait for 60 seconds or more.
2.
Check “Self Diagnostic Result” of “METER/M&A.”
Is “WATER TEMP” displayed?
YES
>> Refer to
MWI-125, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715013
1.
PERFORM SELF-DIAGNOSIS OF ECM
Perform “Self Diagnostic Result” of “ECM.”
Is DTC detected?
YES
>> Perform diagnosis procedure on the detected DTC. Refer to
(MR20DD),
(QR25DE), or
(R9M).
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B2268
WATER TEMP
(Water temperature)
ECM continuously transmits abnormal engine coolant temperature signals for 60 seconds or
more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст