Nissan X-Trail 32. Manual — part 1743
PWC-74
< REMOVAL AND INSTALLATION >
FRONT POWER WINDOW SWITCH
REMOVAL AND INSTALLATION
FRONT POWER WINDOW SWITCH
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Removal and Installation
INFOID:0000000010735257
CAUTION:
Never bend the pawl of power window main switch finisher.
REMOVAL
1.
Disconnect the battery negative terminal. Refer to
PG-142, "EXCEPT FOR R9M : Removal and Installa-
2.
Remove power window main switch finisher. Refer to
INT-14, "Removal and Installation"
.
3.
Remove power window main switch
from power window main
switch finisher
using remover tool (A).
INSTALLATION
Install in the reverse order of removal.
NOTE:
If power window main switch is replaced or is removed, it is necessary to perform the initialization procedure.
Refer to
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Removal and Installation
INFOID:0000000010735258
CAUTION:
Never bend the pawl of front power window switch (passenger side) finisher.
REMOVAL
1.
Remove front power window switch (passenger side) finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Remove front power window switch (passenger side)
from
front power window switch (passenger side) finisher
using
remover tool (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIB3544ZZ
: Pawl
JMKIB3545ZZ
REAR POWER WINDOW SWITCH
PWC-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR POWER WINDOW SWITCH
Removal and Installation
INFOID:0000000010735259
CAUTION:
Never bend the pawl of rear power window switch finisher.
REMOVAL
1.
Remove rear power window switch finisher. Refer to
INT-19, "Removal and Installation"
.
2.
Remove rear power window switch
from rear power window
switch finisher
using remover tool (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIB3546ZZ
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Power Socket . . . . . . . . . . . . . . ....
WIRING DIAGRAM . . . . . . . . . ...
POWER SOCKET . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
POWER SOCKET . . . . . . . . . . . ..
FRONT POWER SOCKET . . . . . . . . . . ..
FRONT POWER SOCKET : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . .
CONSOLE POWER SOCKET . . . . . . . . ....
CONSOLE POWER SOCKET : Removal and In-
stallation . . . . . . . . . . . . . . . . ...
LUGGAGE ROOM POWER SOCKET . . . . . ...
LUGGAGE ROOM POWER SOCKET : Removal
and Installation . . . . . . . . . . . . . .
PWO-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010709174
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing Battery Terminal
INFOID:0000000010709244
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
INSTRUCTION 1
1.
Open the hood.
SEF289H
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст