Nissan X-Trail 32. Manual — part 311
CO-70
< REMOVAL AND INSTALLATION >
[R9M]
RADIATOR
REMOVAL AND INSTALLATION
RADIATOR
Exploded View
INFOID:0000000010782997
REMOVAL
M/T models
JPBIA6920GB
Reservoir tank cap
Reservoir tank
Clamp
Reservoir tank hose
Clamp
Reservoir tank hose
Reservoir tank tube
Reservoir tank hose
Connector
Clamp
Radiator hose (upper)
Radiator
Mounting rubber (upper)
Mounting bracket
O-ring
Air relief plug
Mounting rubber (lower)
O-ring
Drain plug
Clamp
Radiator hose (lower)
Cooling fan assembly
To water inlet
To water connector
To water outlet
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
RADIATOR
CO-71
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
CVT models
Removal and Installation
INFOID:0000000010782998
REMOVAL
WARNING:
• Never remove reservoir tank cap when engine is hot. Serious burns may occur from high-pressure
engine coolant escaping from cooling system.
• Wrap a thick cloth around the reservoir tank cap. Slowly turn it a quarter of a turn to release built-up
pressure. Then turn it all the way.
NOTE:
JPBIA6921GB
Reservoir tank cap
Reservoir tank
Clamp
Reservoir tank hose
Clamp
Reservoir tank hose
Reservoir tank tube
Reservoir tank hose
Connector
Clamp
Radiator hose (upper)
Radiator
Mounting rubber (upper)
Mounting bracket
O-ring
Air relief plug
Mounting rubber (lower)
O-ring
Drain plug
Clamp
Radiator hose (lower)
Connector
Radiator hose (lower)
Clamp
Water hose
Water hose
Cooling fan assembly
To water inlet
To water connector
To water outlet
To CVT oil warmer
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
CO-72
< REMOVAL AND INSTALLATION >
[R9M]
RADIATOR
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Remove engine under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
2.
Drain engine coolant from radiator. Refer to
.
CAUTION:
• Perform this step when the engine is cold.
• Never spill engine coolant on drive belts.
3.
Remove air duct 1 and air duct 2. Refer to
.
4.
Remove front bumper. Refer to
5.
Remove headlamp (RH). Refer to
(LED headlamp models) or
(halogen headlamp models).
6.
Remove charge air cooler. Refer to
.
7.
Remove radiator hose (lower) from radiator.
8.
Disconnect harness connectors from cooling fan assembly, and move harness aside.
9.
Remove condenser
from radiator
according to the follow-
ing instructions:
CAUTION:
• Be careful not to damage condenser core.
• Minimize the moving distance of condenser to prevent
load to air conditioner piping.
a.
Remove bolt
.
b.
Unlock pawl
, and move condenser to rightward of vehicle
(
1).
c.
Move condenser to forward of vehicle (
2).
10. Remove radiator and cooling fan assembly
from the clear-
ance between condenser
and upper radiator core support
.
CAUTION:
• Be careful not to damage radiator core.
• Minimize the moving distance of condenser to prevent
load to air conditioner piping.
11. Remove cooling fan assembly.
REPAIR
If the pin of radiator inserted to mounting rubber breaks, repair according to the following procedure.
1.
Cut the broken pin
at the base.
: Vehicle front
: Vehicle front
: Radiator moving direction
JSBIA5313ZZ
JSBIA5314ZZ
: Radiator
: Cut line
JPBIA6929ZZ
RADIATOR
CO-73
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
2.
Make a hole
in the position that cut the pin.
3.
Install pin
.
INSTALLATION
Note the following, and install in the reverse order of removal.
Radiator hose
CAUTION:
• Use genuine mounting bolts for the cooling fan assembly and strictly observe the tightening torque.
(Breakage prevention for radiator)
NOTE:
• Insert the radiator hose
all the way to the stopper
or by 33 mm (1.30 in) (hose without a stopper).
• For the orientation of the hose clamp pawl, refer to the figure.
: Radiator
Hole's diameter
:
φ
6 mm (0.24 in)
JPBIA6929ZZ
: Radiator
: Nut
JPBIA6931ZZ
Unit: mm (in)
Radiator side
Engine side
JPBIA4294GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст