Nissan X-Trail 32. Manual — part 1120
FLYWHEEL
EM-377
< UNIT DISASSEMBLY AND ASSEMBLY >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1.
Install flywheel by aligning the mark
.
NOTE:
The openings of the flywheel bolts must be aligned.
a.
Install bolts without tightening them.
b.
Fix flywheel using flywheel locking tool [SST: — (Mot.1431)].
c.
Tighten bolts in numerical order as shown in the figure with the
following procedure:
i.
Tighten mounting bolts.
ii.
Turn 50 degrees clockwise (angle tightening).
E1BIA0773ZZ
: 40.0 N·m (4.1 kg-m, 30 ft-lb)
JPBIA0812ZZ
EM-378
< UNIT DISASSEMBLY AND ASSEMBLY >
[R9M]
DRIVE PLATE
DRIVE PLATE
Exploded View
INFOID:0000000011006380
Removal and Installation
INFOID:0000000011006381
REMOVAL
1.
Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the
engine. Refer to
.
2.
Remove drive plate.
CAUTION:
• Never disassemble them.
a.
Fix drive plate using flywheel locking tool [SST: — (Mot.1431)].
b.
Loosen bolts in reverse order as shown in the figure with the fol-
lowing procedure:
3.
Remove pilot bushing using the pilot bushing puller (commercial
service tool), if necessary.
INSTALLATION
1.
Install pilot bushing.
• Using the drift, force fit the pilot bushing until its front end contacts crankshaft.
2.
Install drive plate.
a.
Install bolts without tightening them.
b.
Fix drive plate using flywheel locking tool [SST: — (Mot.1431)].
Pilot bushing
Crankshaft position sensor
Drive plate
To CVT
Comply with the installation proce-
dure when tightening. Refer to
378, "Removal and Installation"
.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPBIA6959GB
E1BIA1163GB
DRIVE PLATE
EM-379
< UNIT DISASSEMBLY AND ASSEMBLY >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
c.
Tighten bolts in numerical order as shown in the figure with the
following procedure:
i.
Tighten mounting bolts.
: 50.0 N·m (5.1 kg-m, 37 ft-lb)
E1BIA1163GB
EM-380
< UNIT DISASSEMBLY AND ASSEMBLY >
[R9M]
OIL PAN (UPPER)
OIL PAN (UPPER)
Exploded View
INFOID:0000000011006384
Removal and Installation
INFOID:0000000010784360
REMOVAL
1.
Remove oil pan (lower). Refer to
2.
Remove oil strainer and oil pump. Refer to
3.
Remove rear oil seal retainer. Refer to
4.
Remove oil pan (upper) with the following procedure:
Oil pan (upper)
Oil pan (lower)
Drain plug washer
Oil pan drain plug
Oil level sensor
Comply with the installation proce-
dure when tightening. Refer to
380, "Removal and Installation"
Comply with the installation proce-
dure when tightening. Refer to
330, "Removal and Installation"
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Sealing point
JPBIA6951GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст