Nissan X-Trail 32. Manual — part 59
AV-228
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U1302 CAMERA POWER VOLT
LHD models without BSW
RHD models with BSW
RHD models without BSW
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
13.
CHECK SIDE CAMERA LH POWER SUPPLY (2)
1.
Turn ignition switch OFF.
2.
Connect following harness connector.
-
Door mirror (driver side) (LHD models)
-
Door mirror (passenger side) (RHD models)
3.
Turn ignition switch ON.
4.
Check the voltage between around view monitor control unit terminals.
LHD models with BSW
LHD models without BSW
RHD models with BSW
Around view monitor control unit
Reference value
(Approx.)
Connector
Terminals
+
–
Terminal
M24
30
29
6.0 V
Around view monitor control unit
Reference value
(Approx.)
Connector
Terminals
+
–
Terminal
M102
62
64
6.0 V
Around view monitor control unit
Reference value
(Approx.)
Connector
Terminals
+
–
Terminal
M24
34
33
6.0 V
Around view monitor control unit
Reference value
(Approx.)
Connector
Terminals
+
–
Terminal
M102
56
58
6.0 V
Around view monitor control unit
Reference value
(Approx.)
Connector
Terminals
+
–
Terminal
M24
30
29
6.0 V
Around view monitor control unit
Reference value
(Approx.)
Connector
Terminals
+
–
Terminal
M102
62
64
6.0 V
AV
U1302 CAMERA POWER VOLT
AV-229
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
RHD models without BSW
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
NO
>> Replace side camera RH. Refer to
AV-271, "Removal and Installation"
Around view monitor control unit
Reference value
(Approx.)
Connector
Terminals
+
–
Terminal
M24
34
33
6.0 V
AV-230
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U1304 CAMERA IMAGE CALIBRATION
U1304 CAMERA IMAGE CALIBRATION
DTC Description
INFOID:0000000010714889
DTC DETECTION LOGIC
POSSIBLE CAUSE
Perform camera calibration
FAIL-SAFE
Unmatched icon
display (red) is displayed (applicable for unmatched camera only).
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn the ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “AVM” using CONSULT.
5.
Check DTC.
Is DTC U1304 detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010714890
1.
PERFORM CALIBRATING CAMERA IMAGE
Perform camera calibration when DTC U1304 is detected.
>> Perform camera calibration. Refer to
AV-161, "CALIBRATING CAMERA IMAGE (AROUND VIEW
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detection condition
U1304
CAMERA IMAGE CALIB
(Camera image calibration)
Camera calibration is incomplete.
NOTE:
Current malfunction is displayed only and is not saved.
AV
U1305 CONFIG UNFINISH
AV-231
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1305 CONFIG UNFINISH
DTC Description
INFOID:0000000010923284
DTC DETECTION LOGIC
POSSIBLE CAUSE
Vehicle specifications for around view monitor control unit is incomplete
FAIL-SAFE
• On applicable camera screen
marking (Red) is displayed.
• Around view monitor with Park Assist is cancel.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn the ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “AVM” using CONSULT.
5.
Check DTC.
Is DTC U1305 detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010923285
1.
PERFORM CONFIGURATION OF AROUND VIEW MONITOR CONTROL UNIT
Perform configuration of around view monitor control unit when DTC U1305 is detected.
>> Perform configuration of around view monitor control unit. Refer to
(AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure"
.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
U1305
CONFIG UNFINISH
(Configuration unfinish)
The vehicle specifications of around view monitor control unit is incomplete.
NOTE:
Current malfunction is displayed only and is not saved.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст