Nissan X-Trail 32. Manual — part 2051
TM-162
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
a.
Expand snap ring at mainshaft rear bearing accessing from the
bore plug hole. Then pull up transaxle case from clutch housing
until snap ring comes off.
b.
While rotating shift lever (outer)
in the direction of the arrow in
the figure, remove transaxle case from clutch housing.
CAUTION:
Never drop each adjusting shim.
NOTE:
Make sure to hold shift lever (outer) in the position shown in the
figure. Otherwise transaxle case cannot be removed from clutch
housing.
12. Remove oil gutter A
and oil gutter B
from transaxle case.
13. Remove snap ring from transaxle case.
14. Remove retaining pin using a pin punch (commercial service
tool) and then remove shift lever (outer) and shift lever (inner)
from transaxle case.
PCIB1840E
JPDIC0140ZZ
: Tab of oil gutter
PCIB1841E
PCIB1842E
PCIB1844E
TRANSAXLE ASSEMBLY
TM-163
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
15. Remove differential side bearing outer race (transaxle case
side) from transaxle case using the puller (A) (SST:
KV381054S0) and then remove differential side bearing adjust-
ing shim from transaxle case.
CAUTION:
Never damage transaxle case and differential side bearing
outer race.
16. Remove differential side oil seal from transaxle case, using oil
seal remover (commercial service tool).
CAUTION:
Never damage transaxle case.
17. Remove shift lever oil seal
and striking rod oil seal
from
transaxle case, using oil seal remover (commercial service tool).
CAUTION:
Never damage transaxle case.
18. Remove striking rod shim
, striking rod adjusting shim
,
mainshaft rear bearing adjusting shim
, input shaft rear bear-
ing adjusting shim
, and reverse idler gear adjusting shim
.
19. Remove retaining pin of reverse shift fork
using a pin punch
(commercial service tool).
JSDIA6487ZZ
SCIA0397E
PCIB1846E
PCIB1858E
: Reverse fork rod
PCIB1850E
TM-164
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
20. Rotate striking lever of striking rod as shown in the figure. Then
rotate reverse fork rod to a position where bracket of reverse
fork rod does not interfere with striking lever of striking rod.
21. Pull out reverse shift fork and reverse fork rod.
22. Remove retaining pin of 5th-6th shift fork
using a pin punch
(commercial service tool).
23. Remove retaining pin of 3rd-4th shift fork
using a pin punch
(commercial service tool).
24. Pull out 3rd-4th fork rod.
25. Pull out 5th-6th shift fork
and 5th-6th fork rod
.
26. Pull out 3rd-4th shift fork
.
PCIB1851E
: 5th-6th fork rod
PCIB1852E
: 3rd-4th fork rod
PCIB1853E
PCIB1854E
PCIB1855E
TRANSAXLE ASSEMBLY
TM-165
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
27. Remove retaining pin of 1st-2nd shift fork
using a pin punch
(commercial service tool).
28. Pull out 1st-2nd shift fork and 1st-2nd fork rod.
29. Remove striking rod assembly
.
30. Remove gear components from clutch housing, as per the fol-
lowing procedure.
a.
Remove a set of input shaft assembly, mainshaft assembly, and
reverse idler gear assembly by tapping the tip of input shaft from
the back of the clutch housing with a plastic hammer.
CAUTION:
Always withdraw mainshaft straight out. Failure to do so
can damage resin oil channel on clutch housing side.
b.
Remove final drive assembly.
31. Remove magnet from clutch housing.
32. Remove mainshaft bearing retainer and then mainshaft front
bearing from clutch housing using the puller (A) (SST:
KV381054S0).
CAUTION:
Never damage clutch housing, mainshaft front bearing, and
oil channel.
33. Remove oil channel from clutch housing.
: 1st-2nd fork rod
PCIB1856E
PCIB1857E
SCIA0964E
PCIB1859E
JSDIA6488ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст