Nissan X-Trail 32. Manual — part 633
HOOD
DLK-873
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove hood lock assembly mounting bolts, and then remove hood lock assembly.
2.
Adjust the surface height of hood assembly according to the specified value by rotating hood bumper rub-
ber.
3.
Loosen hood hinge mounting bolts, and then adjust clearance of hood according to the specified value by
moving the hood assembly.
4.
Tighten hood hinge mounting bolts to the specified torque.
5.
Install hood lock assembly and temporary tighten hood lock
assembly mounting bolts, and then position hood lock assembly
and engage primary striker
. Check hood lock assembly
and primary striker for looseness.
6.
Move hood lock assembly laterally until the center of primary striker and hood lock assembly are vertical
when viewed from the front.
7.
Tighten hood lock assembly mounting bolts to the specified torque.
8.
After adjusting, check that hood opens and closes normally. Refer to
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000010728621
REMOVAL
1.
Remove hood assembly. Refer to
DLK-870, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove upper mounting bolt
of front fender assembly
.
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front grille
–
D
Clearance
7.2 – 11.2
[0.283 – 0.441]
—
Hood –
Front combination lamp
–
E
Clearance
7.0 – 11.0
[0.276 – 0.433]
—
Hood – Front fender
–
F
Clearance
2.5 – 4.5
[0.098 – 0.177]
< 1.4 [0.055]
G
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
< 1.4 [0.055]
JMKIB3498ZZ
JMKIB2955ZZ
DLK-874
< REMOVAL AND INSTALLATION >
[TYPE 4]
HOOD
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Before installation of hood hinge, apply anticorrosive agent onto the mounting surface of the hood
hinge.
• After installation, perform hood fitting adjustment. Refer to
DLK-871, "HOOD ASSEMBLY : Adjust-
• Apply touch-up paint to the body color if the paint around the hinge is peeled off during removal.
• After installation, check that hood opens and closes normally. Refer to
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000010728622
CAUTION:
2 workers are required to support the hood.
REMOVAL
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood
assembly.
2.
Pull hood support rod from grommet and remove it.
INSTALLATION
Install in the reverse order of removal.
RADIATOR CORE SEAL
RADIATOR CORE SEAL : Removal and Installation
INFOID:0000000010728623
REMOVAL
1.
Apply protective tape (A) to hood assembly
around radiator
core seal
fixing clips for preventing damage.
2.
Disengage fixing clips on the reverse side of radiator core seal
using a remover tool (A).
CAUTION:
Never damage hood assembly.
3.
Remove radiator core seal from hood assembly.
INSTALLATION
JMKIB2956ZZ
: Clip
JMKIB2957ZZ
HOOD
DLK-875
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Install in the reverse order of removal.
HOOD INSULATOR
HOOD INSULATOR : Removal and Installation
INFOID:0000000010728624
REMOVAL
1.
Remove hood rod clamp from hood assembly.
2.
Remove hood insulator fixing clips, and then remove hood insulator from hood assembly.
INSTALLATION
Install in the reverse order of removal.
: Clip
JMKIB0387ZZ
DLK-876
< REMOVAL AND INSTALLATION >
[TYPE 4]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
MR20DD
MR20DD : Exploded View
INFOID:0000000010728625
MR20DD : Removal and Installation
INFOID:0000000010728626
RADIATOR CORE SUPPORT UPPER
Removal
1.
Remove air duct 1. Refer to
EM-31, "Removal and Installation"
.
2.
Remove front grille assembly. Refer to
EXT-22, "Removal and Installation"
.
3.
Remove hood lock assembly. Refer to
DLK-910, "HOOD LOCK : Removal and Installation"
.
4.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
Radiator core support upper
Air guide RH
Air lower guide
Air guide LH
Radiator core support lower
Hood lock support stay
: N·m (kg-m, ft-lb)
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB2691GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст