Nissan X-Trail 32. Manual — part 349
DAS
REAR WASHER SWITCH INPUT SIGNAL CIRCUIT
DAS-137
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
REAR WASHER SWITCH INPUT SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000010727946
1.
CHECK COMBINATION SWITCH INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect pump control unit connector and combination switch connector.
3.
Check continuity between combination switch harness connector and pump control unit harness connec-
tor.
4.
Check continuity between pump control unit harness connector and the ground.
Is the inspection result normal?
YES
>> Replace pump control unit. Refer to
DAS-153, "Removal and Installation"
NO
>> Repair harness or connector.
Pump control unit
Combination switch
Continuity
Connector
Terminal
Connector
Terminal
B74
9
M31
11
Existed
Pump control unit
Ground
Continuity
Connector
Terminal
B74
9
Existed
DAS-138
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
BLIND SPOT WARNING INDICATOR CIRCUIT
BLIND SPOT WARNING INDICATOR CIRCUIT
Diagnosis Procedure
INFOID:0000000010727947
1.
CHECK BSW INDICATOR CIRCUIT FOR OPEN 1
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit harness connector and BSW indicator harness connector.
3.
Check continuity between around view monitor control unit harness connector and BSW indicator harness
connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the harnesses or connectors.
2.
CHECK BSW INDICATOR CIRCUIT FOR OPEN 2
Check continuity between BSW indicator harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the harnesses or connectors.
3.
CHECK BSW INDICATOR CIRCUIT FOR SHORT
1.
Turn ignition switch OFF.
2.
Check continuity between around view monitor control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
4.
CHECK AROUND VIEW MONITOR CONTROL UNIT VOLTAGE OUTPUT
1.
Connect around view monitor control unit harness connector.
2.
Check voltage between BSW indicator harness connector and ground.
Around view monitor control
unit
BSW indicator
Continuity
Connector
Terminal
Connector
Terminal
M101
7
D30 (LH)
1
Existed
8
D12 (RH)
BSW indicator
Ground
Continuity
Connector
Terminal
D30 (LH)
4
Existed
D12 (RH)
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M101
7
Not existed
8
DAS
BLIND SPOT WARNING INDICATOR CIRCUIT
DAS-139
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Is the inspection result normal?
YES
>> Replace BSW indicator.
NO
>> Replace the around view monitor control unit. Refer to
AV-268, "Removal and Installation"
Terminal
Condition
Voltage
(Approx.)
(+)
(
−
)
BSW indicator
Ground
Connector
Terminal
D30 (LH)
1
Approx. 2 sec.
after ignition
switch
OFF
⇒
ON
12 V
D12 (RH)
DAS-140
< SYMPTOM DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
DRIVER ASSISTANCE SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
DRIVER ASSISTANCE SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000010727948
Before performing diagnosis, check that it is not a symptom caused by normal operation. Refer to
Symptom
Confirmation item
Inspection item/Reference page
LDW/BSW system display does
not illuminate
All of system display does not illuminate
System settings cannot be
turned ON/OFF
Refer to
Other information display is not illuminated
Combination meter
Refer to
LDW/BSW warning display does
not illuminate (Buzzer is func-
tioning normally)
Information display is func-
tioning normally
LDW
Remove the front camera unit
Refer to
.
BSW
Remove the around view moni-
tor control unit
Refer to
.
Information display is not functioning normally
On board diagnosis function
(Combination meter)
Refer to
LDW/BSW/DAA warning buzzer
is not sounding (Warning display
is functioning normally)
—
Chime does not sound. Refer to
DAS-143, "Diagnosis Proce-
dure"
.
LDW is not functioning normally
LDW system operates even when using turn signal
LDW system operates even
when using turn signal
Refer to
.
Warning functions are not timely
• Does not function when driving on lane markers
• Functions when driving in a lane
• Functions in a different position from the actual position
Front camera unit aiming adjust-
ment
Refer to
BSW is not functioning normally
The system operates once but is cancelled
Check cause of auto-cancel with
BSW
Refer to
.
BSW system does not operates even when using turn signal
BSW system does not operates
even when using turn signal. Re-
fer to
BSW indicator does not illuminate
Refer to
.
Warning functions are not timely
• Does not function when approaching to an adjacent vehicle
• Functions even when the vehicle does not approach to an
adjacent vehicle.
• Functions in a different position from the actual position
• Functions when driving in the middle of lane
Rear camera calibration
Refer to
Rear camera washer is not acti-
vated (Windshield washer is
functioning normally)
—
Refer to
Rear camera wash is insufficient
—
Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст