Nissan X-Trail 32. Manual — part 26

AV-96

< SYSTEM DESCRIPTION >

[WITH NAVIGATION]

DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)

DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)

On Board Diagnosis Function

INFOID:0000000010714805

The NAVI control unit on board diagnosis performs the functions listed in the table below:

ON BOARD DIAGNOSIS ITEM

Mode

Item

Content

Version

—

Version data of the NAVI control unit is
displayed.

User Configuration

• Touch Display Calibration
• Destination Input While

Driving

• Screenshot to USB
• Time interval

—

Allows correction of the position detec-
tion accuracy of the touch panel.

Radio

FM monitor

—

Monitors the dynamic values of the cur-
rent tuner

AM monitor

—

DAB monitor

• Antenna Status
• Field Strength
• Signal Quality
• Audio Mode
• Audio Quality
• Audio Bitrate
• Audio Sampling Rate
• Ensemble Channel
• Ensemble Name
• Ensemble ID
• Service Name
• Service ID
• FM Frequency
• FM PI-Code
• TPEG in current Ensemble

Current status is displayed.

AV

DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)

AV-97

< SYSTEM DESCRIPTION >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Perform CONSULT diagnosis if the NAVI control unit on board diagnosis does not start or the screen does not
display anything.

METHOD OF STARTING

1.

Turn the ignition ON.

2.

Turn the audio system OFF.

3.

While pressing the “SETUP” switch, turn the TUNE-SCROLL
dial counterclockwise 3 or more clicks, then clockwise 3 or more
clicks, then counterclockwise 3 or more clicks. When self diag-
nosis mode begins, a short beep will be heard. Shifting from cur-
rent screen to previous screen is performed by pressing BACK
button.

4.

The trouble diagnosis initial screen is displayed, and Version, User Config, Radio, System State or Self
Test can be selected.

END ON-BOARD DIAGNOSIS

Turn OFF ignition switch.

CONSULT Function

INFOID:0000000010714806

APPLICATION ITEMS

System State

Running System Status

• SD card slot Access
• Power Supply
• Speed Signal
• Direction Signal
• Illumination Signal
• GPS Antenna
• GPS Tracking
• Satellites Visible
• Satellites Tracked
• Microphone Current
• Steer. Wheelkey
• Radio Antenna
• DAB-Antenna
• USB Device
• iPod firmware ver.
• BT Status

The current system status is displayed.

Speaker Test 4 kHz

—

This activates a sequence of test tone
outputs to the audio circuits one after the
other for 1 second.

Speaker Test 100 Hz

Display-Test

—

This provides a test sequence where
test displays (plain colored display: e.g.
white, black, red, blue, green) are shown
one after the other.
The respective color is shown for an in-
dicated period of time (parameter). After
the display test, the design of the display
previously available is stored. While the
screen shows a plain colored display, a
pixel malfunction may be detected.

Self Test

• SD Card Access
• BT Module Access
• GPS Antenna
• Radio Antenna
• DAB-Antenna

A system self test is executed and the
results are stored into the error memory.

Mode

Item

Content

JSNIA7283ZZ

AV-98

< SYSTEM DESCRIPTION >

[WITH NAVIGATION]

DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)

CONSULT performs the following functions via the communication with the NAVI control unit.

ECU IDENTIFICATION

The part number of NAVI control unit is displayed.

SELF DIAGNOSIS RESULT

Refer to

AV-110, "DTC Index"

.

DATA MONITOR

CONFIGURATION

Configuration has three functions as follows.

Diagnosis mode

Description

Ecu Identification

The NAVI control unit part number is displayed.

Self Diagnostic Result

Performs a diagnosis on the NAVI control unit and a connection diagnosis for the communica-
tion circuit of the Multi AV system, and displays the current and past malfunctions collectively.

Data Monitor

The NAVI control unit input/output data is displayed in real time.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing NAVI control unit.

Monitor Item [Unit]

Description

VHCL SPD SIG [On/Off]

Indicates vehicle speed signal received from combination meter on CAN communication
line.

ILLUM SIG [On/Off]

Indicates condition of illumination signal for the NAVI control unit.

IGN SIG [On/Off]

Indicates condition of ignition signal.

REV SIG [On/Off]

Indicates condition of reverse signal received from BCM.

Function

Description

Read/Write Configuration

Before Replace ECU

Allows the reading of vehicle specification written in NAVI control
unit to store the specification in CONSULT.

After Replace ECU

Allows the writing of the vehicle information stored in CONSULT
into the NAVI control unit.

Manual Configuration

Allows the writing of the vehicle specification into the NAVI control
unit by hand.

AV

DIAGNOSIS SYSTEM (AROUND VIEW MONITOR CONTROL UNIT)

AV-99

< SYSTEM DESCRIPTION >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

DIAGNOSIS SYSTEM (AROUND VIEW MONITOR CONTROL UNIT)

CONSULT Function

INFOID:0000000010714807

CONSULT FUNCTIONS

CONSULT performs the following functions via the CAN communication with the around view monitor control
unit.

ECU IDENTIFICATION

Around view monitor control unit part number can be identified.

SELF DIAGNOSIS RESULT

• Refer to

AV-120, "DTC Index"

.

• In CONSULT self-diagnosis, self-diagnosis results and error history are displayed collectively.
• The current malfunction indicates “CRNT”. The past malfunction indicates “PAST”.
• The timing is displayed as “0” if any of the error codes [U1000] and [U1010] is detected. The counter

increases by 1 if the condition is normal at the next ignition switch ON cycle.

Freeze Frame Data (FFD)

The following vehicle status is recorded when DTC is detected and is displayed on CONSULT.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
• Displays the status of the following vehicle signals inputted into the around view monitor control unit.
• For each signal, actual signal can be compared with the condition recognized on the system.

Diagnosis mode

Description

ECU Identification

Around view monitor control unit part number can be identified.

Self Diagnostic Results

Around view monitor control unit diagnosis is performed. Current and previous malfunctions are
displayed collectively.

Data Monitor

Diagnosis of vehicle signal that is received by around view monitor control unit can be per-
formed.

Work Support

• Calibration and initialization of each camera can be performed.
• Fine tuning of Birds-eye view can be performed.
• Target line calibration of rear wide view can be performed.
• Language of warning message can be selected.
• Display of predicted course line can be switched to ON/OFF.
• Neutral position adjustment of steering angle sensor can be performed.
• Camera screen activation enhancing display can be switched to ON/OFF.
• Calibration for BSW can be performed.
• Displays causes of system cancellation occurred during system control.

Active Test

Enables an operational check of a load by transmitting a driving signal from the around view
monitor control unit to the load.

Configuration

• The vehicle specification that is written in around view monitor control unit can be displayed

or stored.

• The vehicle specification can be written when around view monitor control unit is replaced.

Item name

Display content

ODO/TRIP
METER
(km)

Total driving distance (odometer value) upon DTC detection is displayed.

Display Item

Remarks

ST ANGLE SENSOR SIGNAL
[ON/OFF]

Receiving status of steering angle signal received from steering angle sensor is switched to
ON/OFF.

REVERSE SIGNAL
[ON/OFF]

Receiving status of reverse signal received from NAVI control unit is displayed by ON/OFF.