Nissan X-Trail 32. Manual — part 2016
TM-22
< SYSTEM DESCRIPTION >
[6MT: RS6F94R]
STRUCTURE AND OPERATION
STRUCTURE AND OPERATION
Sectional View
INFOID:0000000010842438
3rd input gear
3rd-4th synchronizer hub assembly
4th input gear
5th input gear
5th-6th synchronizer hub assembly
6th input gear
Transaxle case
6th main gear
5th main gear
4th main gear
3rd main gear
2nd main gear
1st-2nd synchronizer hub assembly
1st main gear
Differential
Final gear
Mainshaft
Input shaft
Clutch housing
Reverse idler shaft
Reverse input gear
Reverse output gear
JPDIC0631ZZ
STRUCTURE AND OPERATION
TM-23
< SYSTEM DESCRIPTION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
System Description
INFOID:0000000010842439
TRIPLE-CONE SYNCHRONIZER
Triple-cone synchronizers are adopted for the 1st and the 2nd gears
to reduce operating force of the shift lever.
REVERSE GEAR NOISE PREVENTION FUNCTION (SYNCHRONIZING METHOD)
Reverse gear assembly consists of reverse input gear, return spring,
reverse baulk ring, and reverse output gear. When the shift lever is
shifted to the reverse position, the construction allows smooth shift
operation by stopping the reverse idler shaft rotation by frictional
force of synchronizer.
: 1st main gear
: 1st-2nd coupling sleeve
: Insert key
: Outer baulk ring
: 2nd main gear
: Synchronizer cone
: Inner baulk ring
: 1st-2nd synchronizer hub
SCIA7636E
: Reverse fork rod
: Reverse output gear
: Return spring
: Reverse baulk ring
: Reverse input gear
SCIA7621E
TM-24
< DTC/CIRCUIT DIAGNOSIS >
[6MT: RS6F94R]
POSITION SWITCH
DTC/CIRCUIT DIAGNOSIS
POSITION SWITCH
Component Function Check
INFOID:0000000010929178
1.
REVERSE POSITION SIGNAL OUTPUT CHECK
1.
Turn the ignition switch OFF.
2.
Disconnect position switch harness connector.
3.
Operate shift lever to each position and check continuity
between position switch terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to
2.
NEUTRAL POSITION SIGNAL OUTPUT CHECK
Operate shift lever to each position and check continuity between
position switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
Diagnosis Procedure
INFOID:0000000010929196
1.
CHECK POSITION SWITCH
Check position switch. Refer to
.
Is the inspection results normal?
YES
>> Repair shift control function or transaxle for mechanical malfunction.
NO
>> Replace position switch. Refer to
TM-36, "Removal and Installation"
.
Component Inspection
INFOID:0000000010842440
1.
CHECK BACK-UP LAMP SWITCH
1.
Turn the ignition switch OFF.
2.
Disconnect position switch harness connector.
3.
Remove position switch. Refer to
TM-36, "Removal and Installation"
Terminals
Condition
Continuity
1
2
Reverse gear position
Existed
Except reverse gear position
Not existed
PCIB1781E
Terminals
Condition
Continuity
2
3
Neutral gear position
Existed
Except neutral gear position
Not existed
JPDIC0091ZZ
POSITION SWITCH
TM-25
< DTC/CIRCUIT DIAGNOSIS >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Check continuity between position switch terminals.
NOTE:
When shift lever is in reverse gear position, plunger is pressed.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace position switch. Refer to
2.
CHECK PARK/NEUTRAL POSITION (PNP) SWITCH
Check continuity between position switch terminals.
NOTE:
When shift lever is in neutral gear position, plunger is slightly
pressed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace position switch. Refer to
TM-36, "Removal and Installation"
.
Terminals
Condition
Continuity
1
2
Plunger
is
pressed.
Existed
Plunger
is
released.
Not existed
JSDIA5832ZZ
Terminals
Condition
Continuity
2
3
Plunger
is fully pressed and fully released.
Not existed
Plunger
is pressed approx. 2 mm (0.08 in).
Existed
JSDIA5833ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст