Nissan X-Trail 32. Manual — part 1047
CAMSHAFT
EM-85
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1.
Measure the camshaft cam height with a micrometer (A).
2.
If it exceeds the limit, replace camshaft.
Camshaft Journal Oil Clearance
CAMSHAFT JOURNAL OUTER DIAMETER
Measure the outer diameter of camshaft journal with a micrometer
(A).
CAMSHAFT BRACKET INNER DIAMETER
• Tighten camshaft bracket bolts with specified torque. Refer to
EM-81, "Removal and Installation"
• Measure the inner diameter of camshaft bracket with a cylinder
gauge .
CAMSHAFT JOURNAL OIL CLEARANCE
• (Oil clearance) = (Camshaft bracket inner diameter) – (Camshaft journal diameter)
• If it exceeds the limit, replace camshaft or cylinder head, or both.
NOTE:
Camshaft bracket cannot be replaced as a single part, because it is machined together with cylinder head.
Replace whole cylinder head assembly.
Camshaft End Play
1.
Install camshaft in cylinder head. Refer to
EM-81, "Removal and Installation"
Standard and Limit
: Refer to
.
JPBIA6382ZZ
Standard
: Refer to
JPBIA6337ZZ
: Measuring direction of inner diameter
Standard
: Refer to
PBIC3180J
Standard and Limit
: Refer to
.
EM-86
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
CAMSHAFT
2.
Install dial indicator in thrust direction on front end of camshaft.
Read the end play of dial indicator
when camshaft is moved
forward/backward (in direction to axis).
• Measure the following parts if out of the standard.
- Dimension (A) for groove of cylinder head No. 1 journal
- Dimension (B) for camshaft flange
• Refer to the standards above, and then replace camshaft and/
or cylinder head.
Camshaft Sprocket Runout
1.
Put V-block on precise flat table, and support No. 2 and 5 journals of camshaft.
CAUTION:
Never support No. 1 journal (on the side of camshaft sprocket) because it has a different diameter
from the other four locations.
2.
Measure the camshaft sprocket runout with a dial indicator (A).
(Total indicator reading)
• If it exceeds the limit, replace camshaft sprocket.
Valve Lifter
Check if surface of valve lifter has any wear or cracks.
• If anything above is found, replace valve lifter. Refer to
.
Valve Lifter Clearance
VALVE LIFTER OUTER DIAMETER
Standard and Limit
: Refer to
.
PBIC3181J
Standard
: 4.000 - 4.030 mm (0.1575 - 0.1587 in)
Standard
: 3.877 - 3.925 mm (0.1526 - 0.1545 in)
PBIC3183J
Limit
: Refer to
.
JPBIA4413ZZ
KBIA0182E
CAMSHAFT
EM-87
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Measure the outer diameter of valve lifter with a micrometer (A).
VALVE LIFTER HOLE DIAMETER
Measure the inner diameter of valve lifter hole of cylinder head with
an inside micrometer
.
VALVE LIFTER CLEARANCE
• (Valve lifter clearance) = (Valve lifter hole diameter) – (Valve lifter
outer diameter)
• If out of the standard, referring to the each standard of valve lifter
outer diameter and valve lifter hole diameter, replace either or both
valve lifter and cylinder head.
INSPECTION AFTER INSTALLATION
Inspection of Camshaft Sprocket (INT), (EXH) Oil Groove
CAUTION:
• Perform this inspection only when DTC P0011 or P0014 is detected in self-diagnostic results of CON-
SULT and it is directed according to inspection procedure of EC section. Refer to
(P0011) or
• Check when engine is cold so as to prevent burns by the splashing engine oil.
1.
Check engine oil level. Refer to
.
2.
Perform the following procedure so as to prevent the engine from being unintentionally started while
checking.
a.
Release the fuel pressure. Refer to
.
b.
Remove intake manifold. Refer to
c.
Disconnect ignition coil and injector harness connectors.
d.
Support the bottom surface of engine using a transmission jack, and then remove the engine mounting
bracket (RH) and engine mounting insulator (RH). Refer to
3.
Remove intake or exhaust valve timing control solenoid valve. Refer to
.
• Lift the front side of the engine with a jack base to remove intake or exhaust valve timing control sole-
noid valve.
4.
Clean the mounting area of intake or exhaust valve timing control solenoid valve, and then insert a clean
waste with no oil adhesion into the oil hole of the cylinder head.
5.
Install engine mounting insulator (RH) and engine mounting bracket (RH). (After the removal of intake or
exhaust valve timing control solenoid valve and insertion of a waste into the oil hole.)
6.
Perform cranking to check that engine oil comes out from the oil hole (mounting hole of intake or exhaust
valve timing control solenoid valve) of cylinder head.
• Regarding the engine oil check, judge it by the amount of oil adhered to the wasted inserted into the oil
hole.
WARNING:
• Never insert fingers into the oil hole.
• Never touch rotating parts (drive belt, idler pulleys and crankshaft pulley, etc.).
CAUTION:
Standard
: Refer to
.
JPBIA0125ZZ
Standard
: Refer to
.
Standard
: Refer to
.
PBIC3184J
EM-88
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
CAMSHAFT
• Never perform cranking without installing the engine mounting insulator (RH) and engine mount-
ing bracket (RH).
• Prevent splashing by using a shop cloth so as to prevent the worker from injury from engine oil
and so as to prevent engine oil contamination.
• Prevent splashing by using a shop cloth so as to prevent engine oil from being splashed to
engine and vehicle. Especially, be careful not to apply engine oil to rubber parts of drive belt,
engine mounting insulator, etc. Wipe engine oil off immediately if it is splashed.
7.
Perform the following inspection if engine oil does not come out from intake or exhaust valve timing con-
trol solenoid valve oil hole of the cylinder head.
• Clean oil groove between oil strainer and intake valve timing control solenoid valve. Refer to
LU-8, "Engine Lubrication System Schematic"
8.
Remove components between intake or exhaust valve timing control solenoid valve and camshaft
sprocket (INT) or (EXH), and then check each oil groove for clogging.
• Clean oil groove if necessary. Refer to
LU-7, "Engine Lubrication System"
.
9.
After inspection, install removed parts in the reverse order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст