Nissan X-Trail 32. Manual — part 232
REPAIRING HIGH STRENGTH STEEL
BRM-89
< PRECAUTION >
[FOR EUROPE (RHD)]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
• When welding HSS panels, use spot welding whenever possi-
ble in order to minimize weakening surrounding areas due to
heat.
If spot welding is impossible, use MIG. welding. Do not use
gas (torch) for welding because it is inferior in welding
strength.
• Spot welding on HSS panels is harder than that of an ordinary
steel panel.
Therefore, when cutting spot welds on a HSS panel, use a low
speed high torque drill (1,000 to 1,200 rpm) to increase drill bit
durability and facilitate the operation.
2.
Precautions in spot welding HSS
This work should be performed under standard working condi-
tions. Always note the following when spot welding HSS:
• The electrode tip diameter must be sized properly according to
the metal thickness.
• The panel surfaces must fit flush to each other, leaving no
gaps.
PIIA0144E
PIIA0145E
PIIA0146E
PIIA0147E
BRM-90
< PRECAUTION >
[FOR EUROPE (RHD)]
REPAIRING HIGH STRENGTH STEEL
• Follow the specifications for the proper welding pitch.
Unit: mm (in)
Thickness (T)
Minimum pitch (L)
0.6 (0.024)
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.6 (0.063)
1.8 (0.071)
10 (0.39) or more
12 (0.47) or more
18 (0.71) or more
20 (0.79) or more
27 (1.06) or more
31 (1.22) or more
JSKIA0781ZZ
REPAIRING MATERIAL
BRM-91
< PREPARATION >
[FOR EUROPE (RHD)]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
PREPARATION
REPAIRING MATERIAL
Foam Repair
INFOID:0000000010843492
During factory body assembly, foam insulators are installed in certain body panels and locations around the
vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.
URETHANE FOAM APPLICATIONS
Use commercially available Urethane foam for sealant (foam material) repair of material used on vehicle.
Read instructions on product for fill procedures.
Example of foaming agent filling operation procedure
1.
Fill procedures after installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating form insulator and foam material.
c.
Install service part.
d.
Insert nozzle into hole near fill area and fill foam material or fill enough to close gap with the service part.
2.
Fill procedures before installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating foam insulator and foam material.
c.
Fill foam material on wheelhouse outer side.
<Urethane foam for foaming agent>
3M™ Automix™ Flexible Foam 08463 or equiva-
lent
Urethane foam
Nozzle insert hole
: Vehicle front
JSKIA0129GB
BRM-92
< PREPARATION >
[FOR EUROPE (RHD)]
REPAIRING MATERIAL
NOTE:
Fill enough to close gap with service part while avoiding flange
area.
d.
Install service part.
NOTE:
Refer to label for information on working times.
Urethane foam
Fill while avoiding flange area
: Vehicle front
JSKIA0130GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст