Nissan X-Trail 32. Manual — part 1592
MWI-50
< SYSTEM DESCRIPTION >
SYSTEM
WARNING LAMPS/INDICATOR LAMPS : Malfunction Indicator Lamp (MIL)
INFOID:0000000010781002
DESIGN/PURPOSE
When a malfunction which increases exhaust gases is detected, ECM turns ON MIL and informs the driver of
the necessity of inspection and repair.
When a malfunction which causes damage to the catalyst is
detected, ECM immediately blinks MIL to alert the driver.
NOTE:
For R9M engine models
• ECM turns ON MIL (yellow) when an emission-related malfunction
occurs or when a component part specified by European laws and
regulations becomes inoperable three trips in a raw. (Yellow)
• ECM may turn ON MIL (red) when a malfunction occurs in the
engine. (Red)
BULB CHECK
Take away warning
X
DLK-60, "INFORMATION DISPLAY (COMBINA-
TION METER) : Take Away Warning (Information
Display)"
(TYPE1), or
DISPLAY (COMBINATION METER) : Take Away
Warning (Information Display)"
(TYPE2)
NOTE:
To identify vehicle type, refer to
.
4WD warning
X
DLN-22, "INFORMATION DISPLAY (COMBINA-
TION METER) : 4WD Warning"
(TY21C), or
126, "INFORMATION DISPLAY (COMBINATION
METER) : 4WD Warning"
Headlamp warning
X
X
EXL-49, "INFORMATION DISPLAY (COMBINA-
TION METER) : Headlamp Warning"
LDW system display (warning)
X
DAS-30, "LDW : Menu Displayed by Pressing
Each Switch"
BSW system display (warning)
X
DAS-33, "BSW : Menu Displayed by Pressing
Each Switch"
DAA system display (warning)
X
DAS-38, "DAA : Menu Displayed by Pressing Each
Switch"
TSR system display (warning)
X
DAS-36, "TSR : Menu Displayed by Pressing Each
Switch"
FEB system display (warning)
X
BRC-238, "Menu Displayed by Pressing Each
Switch"
Parking sensor error
X
SN-17, "INFORMATION DISPLAY (COMBINA-
TION METER) : Parking Sensor Error"
PARK ASSIST), or
PLAY (COMBINATION METER) : Parking Sensor
Error"
(WITH PARK ASSIST)
Chassis control display (warning)
X
DAS-187, "INFORMATION DISPLAY (COMBINA-
TION METER) : Chassis Control Display"
Oil level sensor warning
X
MWI-67, "WARNING/INDICATOR (ON INFORMA-
TION DISPLAY) : Oil Level Warning"
Low tire pressure location indicator
X
WT-12, "INFORMATION DISPLAY (COMBINA-
TION METER) : Low Tire Pressure Location Indi-
cator"
Information display warning item
Master warning lamp
Reference
Red
Yellow
JPNIA1882ZZ
MWI
SYSTEM
MWI-51
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
The bulb turns ON after turning ON the ignition switch (engine stop) and turns OFF after restarting the engine.
SYNCHRONIZATION WITH MASTER WARNING
Not applicable
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIG-
NAL
For the operation for CAN communication blackout in the combination meter, refer to
.
SYSTEM DIAGRAM
SIGNAL PATH
• When the lighting conditions of the malfunction indicator lamp (MIL) are satisfied, ECM transmits a malfunc-
tion indicator lamp (MIL) signal to the combination meter via CAN communication.
• The combination meter turns ON or blinks the malfunction indicator lamp (MIL), according to a signal
received from ECM.
LIGHTING CONDITION
When all of the following conditions are satisfied:
• Ignition switch: ON
• DTC which influences on exhaust gasses is judged.
NOTE:
For R9M engine models
• For DTCs that the malfunction indicator lamp turns ON and the number of DTC diagnosis trips, refer to
(Yellow/Red).
SHUTOFF CONDITION
When any of the following conditions is satisfied:
• Ignition switch: OFF
• Erase DTC
JPBIA6021GB
MWI-52
< SYSTEM DESCRIPTION >
SYSTEM
TIMING CHART
WARNING LAMPS/INDICATOR LAMPS : Position Lamp Indicator Lamp
INFOID:0000000010782908
DESIGN/PURPOSE
Position lamp indicator lamp informs the driver that parking lamp,
license plate lamp and tail lamp are in ON status.
BULB CHECK
Not applicable
SYNCHRONIZATION WITH MASTER WARNING LAMP
Not applicable
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIG-
NAL
For actions on CAN communications blackout in the combination meter, refer to
SYSTEM DIAGRAM
JPBIA6022GB
JPNIA1880ZZ
JMLIA4106GB
MWI
SYSTEM
MWI-53
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SIGNAL PATH
• BCM transmits position light request signal to combination meter via CAN communication when parking
lamp, license plate lamp and tail lamp are in ON status.
• When combination meter receives position light request signal, combination meter turns position lamp indi-
cator lamp ON.
LIGHTING CONDITION
When parking lamp, license plate lamp and tail lamp are turned ON.
SHUTOFF CONDITION
When parking lamp, license plate lamp and tail lamp are turned OFF.
WARNING LAMPS/INDICATOR LAMPS : Rear Fog Lamp Indicator Lamp
INFOID:0000000010782909
DESIGN/PURPOSE
Rear fog lamp indicator lamp informs the driver that rear fog lamp is
in ON status.
BULB CHECK
Not applicable
SYNCHRONIZATION WITH MASTER WARNING LAMP
Not applicable
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIG-
NAL
For actions on CAN communications blackout in the combination meter, refer to
SYSTEM DIAGRAM
SIGNAL PATH
• BCM transmits rear fog lamp status signal to combination meter via CAN communication when rear fog lamp
is in ON status.
• When combination meter receives rear fog lamp status signal, combination meter turns rear fog lamp indica-
tor lamp ON.
LIGHTING CONDITION
JPNIA1879ZZ
JMLIA4107GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст