Nissan X-Trail 32. Manual — part 508
SYSTEM (AUTOMATIC BACK DOOR SYSTEM)
DLK-373
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Operation Condition
When all of the following conditions are satisfied.
• Vehicle speed: 0 km/h
• Shift position: P position
• Automatic back door main switch: ON position (hands free function ON)
• Back door: Full closed
• Intelligent Key: Within outside key antenna (rear bumper) detection area
Operation Description
• When the back door is fully closed and the operating conditions are satisfied, automatic back door control
unit supplies power to hands free sensor.
• When a hand or baggage is held over the hands free sensor is shaded with a hand or baggage for approxi-
mately 1 second while carrying the Intelligent Key, the hand free sensor transmits hands free sensor signal
to BCM.
• BCM receives the hands free sensor signal, and then activates the outside key antenna (rear bumper), and
checks that the Intelligent Key is near the rear bumper.
• When Intelligent Key is within the detection area of outside key antenna (rear bumper), the Intelligent Key
receives the request signal and transmits the key ID signal to BCM via remote keyless entry receiver (inte-
grated in BCM).
• BCM receives the key ID signal and verifies the received key ID with the registered key ID.
• When the key IDs match, BCM transmits back door open request signal to the automatic back door control
unit. All doors are unlocked simultaneously.
• Once automatic back door operation request signal is received from BCM, the automatic back door control
unit activates the automatic open function and automatically opens the back door to the fully open position
*
.
*
: Fully open position can be changed with the back door fully open position setting function.
NOTE:
• Hands free function does not operate when, an object that absorbs light (leather glove, etc.) is held over the
hands free sensor for approximately 1 second, while Intelligent Key is carried.
• When the hands free sensor is exposed to the light of headlamp and/or the sun, or when an accessory, such
as a frame, is attached to the license plate, the hands free function may not operate.
Hands Free Sensor Detection Area
Setting position
Automatic back door open/close
function
Hands free function
ON
ON
ON
OFF
OFF
OFF
OFF
JMKIB2820ZZ
JMKIB2821ZZ
DLK-374
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (AUTOMATIC BACK DOOR SYSTEM)
The hands free sensor detection area of hands free function is in the
range of approximately 80 mm surrounding the hands free sensor.
AUTOMATIC BACK DOOR OPEN/CLOSE FUNCTION
• In the case of the back door fully closed, operate the automatic back door switch, Intelligent Key or back
door opener switch with the back door unlock. The back door closure motor releases the latch, then the spin-
dle motor opens the back door to the fully open position. The closure motor reverses to the neutral position
simultaneously.
• In the case of the back door fully open, operate the automatic back door switch, Intelligent Key or automatic
back door close switch. The spindle motor closes the back door to the half-latch position, then the back door
closure motor to the full latch position. Then, the closure motor reverses to the neutral position.
Operation Condition
When all of the following conditions are satisfied.
• Shift position: P position (CVT models)
• Parking brake: ON (M/T models)
• Vehicle speed: 0 km/h
• Power supply (automatic power back door control unit): Approx. 11 V or more
Automatic Open/close Operation When Each Switch is Operated
The automatic open/close operation when each switch is operated differs according to the stop position or
operating status of back door. Refer to the following.
Automatic back door switch
JMKIB3491GB
JMKIB3531GB
Condition
Back door operation
Back door position
Automatic back door
main switch
Back door condition
Automatic back door
switch
Full open
ON
Stop
Long press (1 sec)
Perform the auto close
function
Fully open to just before
fully open
ON
Stop
Long press (1 sec)
Perform the auto close
function
–
Auto open function op-
erating
Press
Perform the auto close
function (reverse oper-
ation)
–
Auto close function op-
erating
Press
Operation is continued
SYSTEM (AUTOMATIC BACK DOOR SYSTEM)
DLK-375
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Intelligent Key
Middle
–
Stop
Press
Non-operation (manual
movement only)
–
Auto open function op-
erating
Press
Perform the auto close
function (reverse oper-
ation)
–
Auto close function op-
erating
Press
Perform the auto open
function (reverse oper-
ation)
Just before fully closed
to fully closed
–
Stop
Press
Non-operation (manual
movement only)
–
Auto open function op-
erating
Press
Operation is continued
–
Auto close function op-
erating
Press
Perform the auto open
function (reverse oper-
ation)
Full closed
ON
Stop
Long press (1 sec)
Perform the auto open
function
Condition
Back door opera-
tion
Back door position
Ignition switch
Automatic back
door main switch
Back door condi-
tion
Intelligent Key
Full open
OFF
–
Stop
Long press (1 sec)
Perform the auto
close function
Fully open to just
before fully open
OFF
–
Stop
Long press (1 sec)
Perform the auto
close function
OFF
–
Auto open function
operating
Long press (1 sec)
Perform the auto
close function (re-
verse operation)
OFF
–
Auto close function
operating
Long press (1 sec)
Operation is contin-
ued
Middle
OFF
–
Stop
Long press (1 sec)
Non-operation
(manual movement
only)
OFF
–
Auto open function
operating
Long press (1 sec)
Perform the auto
close function (re-
verse operation)
OFF
–
Auto close function
operating
Long press (1 sec)
Perform the auto
open function (re-
verse operation)
Just before fully
closed to fully
closed
OFF
–
Stop
Long press (1 sec)
Non-operation
(manual movement
only)
OFF
–
Auto open function
operating
Long press (1 sec)
Operation is contin-
ued
OFF
–
Auto close function
operating
Long press (1 sec)
Perform the auto
open function (re-
verse operation)
Full closed
OFF
–
Stop
Long press (1 sec)
Perform the auto
open function
Condition
Back door operation
Back door position
Automatic back door
main switch
Back door condition
Automatic back door
switch
DLK-376
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (AUTOMATIC BACK DOOR SYSTEM)
Automatic back door close switch
Back door opener switch
Condition
Back door operation
Back door position
Automatic back door
main switch
Back door condition
Automatic back door
close switch
Full open
ON
Stop
Press
Perform the auto close
function
Fully open to just before
fully open
ON
Stop
Press
Perform the auto close
function
–
Auto open function op-
erating
Press
Perform the auto close
function (reverse oper-
ation)
–
Auto close function op-
erating
Press
Operation is continued
Middle
ON
Stop
Press
Perform the auto close
function
–
Auto open function op-
erating
Press
Perform the auto close
function (reverse oper-
ation)
–
Auto close function op-
erating
Press
Perform the auto open
function (reverse oper-
ation)
Just before fully closed
to fully closed
–
Stop
Press
Non-operation (manual
movement only)
–
Auto open function op-
erating
Press
Operation is continued
–
Auto close function op-
erating
Press
Perform the auto open
function (reverse oper-
ation)
Condition
Back door operation
Back door position
Automatic back door
main switch
Back door condition
Back door opener
switch
Full open
–
Stop
Press
Non-operation
Fully open to just before
fully open
–
Stop
Press
Non-operation
–
Auto open function op-
erating
Press
Operation stop (auto-
matic open/close tem-
porary stop function)
–
Auto close function op-
erating
Press
Operation stop (auto-
matic open/close tem-
porary stop function)
Middle
ON
Stop
Press
Perform the auto open
function
–
Auto open function op-
erating
Press
Operation stop (auto-
matic open/close tem-
porary stop function)
–
Auto close function op-
erating
Press
Operation stop (auto-
matic open/close tem-
porary stop function)
Just before fully closed
to fully closed
ON
Stop
Press
Perform the auto open
function
–
Auto open function op-
erating
Press
Operation stop (auto-
matic open/close tem-
porary stop function)
–
Auto close function op-
erating
Press
Operation stop (auto-
matic open/close tem-
porary stop function)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст