Nissan X-Trail 32. Manual — part 1772
RSU-10
< REMOVAL AND INSTALLATION >
COIL SPRING
• Securely install coil spring with the lower end aligned with the
steps of lower rubber seat.
CAUTION:
The lower rubber seat protrusion must be securely inserted
into the hole of rear suspension arm.
• Install coil spring
by aligning lower end of coil spring with lower
rubber seat
as shown in the figure.
CAUTION:
Set coil spring so that its paint mark
is aligned with the
position of 1.75 turns from the bottom end of the coil spring.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010822780
INSPECTION AFTER REMOVAL
Check rear lower link, rubber seat, upper seat, and coil spring for deformation, crack, and damage. Replace it
if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
.
SEIA0636J
Dimension (A)
: 5 mm (0.20 in) or less
JSEIA0671ZZ
ALEIA0210ZZ
REAR SHOCK ABSORBER
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000010822781
Removal and Installation
INFOID:0000000010822782
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Set jack (A) under suspension arm to relieve the coil spring tension.
CAUTION:
• Check the stable condition when using a jack.
• Never damage suspesion arm with a jack.
3.
Remove shock absorber mounting bolt (Upper and lower side).
4.
Remove shock absorber.
5.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
• After replacing the shock absorber, always follow the disposal procedure to discard the shock absorber.
.
Inspection
INFOID:0000000010822783
INSPECTION AFTER DISASSEMBLY
Check the following items, and replace the part if necessary.
• Shock absorber for deformation, cracks, and other damage.
• Piston rod for damage, uneven wear, and distortion.
• Oil leakage
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
Rear suspension member
shock absorber
Suspension arm
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0904GB
RSU-12
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
2.
Adjust neutral position of steering angle sensor. Refer to
.
Disposal
INFOID:0000000010822784
1.
Set shock absorber horizontally to the ground with the piston rod fully extracted.
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction show by arrow.
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
REAR SUSPENSION ARM
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION ARM
Exploded View
INFOID:0000000010822785
Removal and Installation
INFOID:0000000010822786
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Drain brake fluid.
• LHD: Refer to
• RHD: Refer to
.
3.
Remove wheel sensor and sensor harness. Refer to
BRC-214, "REAR WHEEL SENSOR : Removal and
.
4.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD: Refer to
BR-63, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
• RHD: Refer to
BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• 4WD: Refer to
RAX-18, "Removal and Installation"
.
CAUTION:
• Put matching marks on the wheel hub assembly and the disc rotor before removing the disc
rotor.
• Never drop disc rotor.
6.
Remove parking brake cable mounting bolt. Refer to
7.
Separate the brake tube from the brake hose, and then remove rock plate.
• LHD: Refer to
BR-29, "REAR : Removal and Installation"
• RHD: Refer to
BR-92, "REAR : Removal and Installation"
.
8.
Remove brake tube from suspension arm.
• LHD: Refer to
Suspension arm bracket
Suspension bar
Arm stopper
Suspension arm
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0906GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст