Nissan X-Trail 32. Manual — part 1677
PCS-78
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
DIAGNOSIS SYSTEM (BCM)
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Without Super
Lock)
INFOID:0000000010869013
WORK SUPPORT
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
SHORT CRANKING OUTPUT
NOTE:
This item is displayed, but cannot be monitored
IGN/ACC BATTERY SAVER
Ignition battery saver system mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK I-KEY LOCK UN-
LOCK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS LOCK
UNLOCK
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
PCS
DIAGNOSIS SYSTEM (BCM)
PCS-79
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
NEUTRAL SW - IPDM
Indicates [On/Off] condition of reverse/neutral position switch
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
STARTER RELAY - IPDM
Indicates [On/Off] condition of starter relay
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communi-
cation
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS actuator and electric unit (control unit) by
numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected in-
side vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
Monitor Item
Condition
PCS-80
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
DIAGNOSIS SYSTEM (BCM)
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intel-
ligent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/On] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC
(CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
Indicates [On/Off] condition of back door open request signal from Intelligent Key
KEY SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
PCS
DIAGNOSIS SYSTEM (BCM)
PCS-81
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: [Intelligent Key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
NOTE:
This item is displayed, but cannot be used
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
NOTE:
This item is displayed, but cannot be used
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст