Nissan X-Trail 32. Manual — part 338
DAS
ACTION TEST
DAS-93
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
1.
Enable the setting of the BSW system on the combination meter.
2.
Check BSW operation according to the following table.
NOTE:
• If vehicle speed exceeds approximately 32 km/h (20 MPH), BSW function operates until the vehicle
speed becomes lower than approximately 29 km/h (18 MPH).
• Time shown in the figure is approximate time.
>> INSPECTION END
TSR
Vehicle condition/ Driver's opera-
tion
Action
Vehicle
speed
(Approx.)
Turn sig-
nal con-
dition
Status of
vehicle
detection
within de-
tection
area
Indication
on the
BSW indi-
cator
Indication on the combination meter
Buzzer
Upper part
Middle part
Less than
29 km/h
(18 MPH)
—
—
OFF
White
White
OFF
32 km/h
(20 MPH)
or more
—
Vehicle is
not de-
tected
OFF
White
White
OFF
OFF
Vehicle is
detected
ON
White
White
OFF
ON
(vehicle
detect-
ed direc-
tion)
Before
turn sig-
nal oper-
ates
Vehicle is
detected
Blink
Orange (Blink)
Orange (Blink)
Short
contin-
uous
beeps
Vehicle is
detected
after turn
signal op-
erates
Blink
Orange (Blink)
Orange (Blink)
OFF
JSOIA1423ZZ
JSOIA1597ZZ
JSOIA1423ZZ
JSOIA1597ZZ
JSOIA1423ZZ
JSOIA1597ZZ
JSOIA1425ZZ
JSOIA1600ZZ
JSOIA1425ZZ
JSOIA1600ZZ
DAS-94
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
TSR : Description
INFOID:0000000010927844
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-8, "Precaution for TSR System Service"
- System description for TSR: Refer to
DAS-21, "TSR : System Description"
- Handling precaution: Refer to
DAS-41, "Precautions for Traffic Sign Recognition"
TSR : Work Procedure
INFOID:0000000010927845
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-8, "Precaution for TSR System Service"
- System description for TSR: Refer to
DAS-21, "TSR : System Description"
- Handling precaution: Refer to
DAS-41, "Precautions for Traffic Sign Recognition"
1.
CHECK TSR SYSTEM SETTING
1.
Start the engine.
2.
After starting the engine wait for 30 seconds or more.
3.
Enable the setting of the TSR system on the combination meter.
4.
Turn OFF the ignition switch and wait for 5 seconds or more.
5.
Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR LDW
1.
Enable the setting of the TSR system on the combination meter.
2.
Check the TSR operation according to the following table.
System status
Condition
Display on combination meter
Upper part
Middle part
TSR OFF
—
—
JSOIA1611ZZ
DAS
ACTION TEST
DAS-95
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
>> INSPECTION END
DAA
DAA : Description
INFOID:0000000010927846
Always perform the TSR system action test to check that the system operates normally after replacing the
around view monitor control unit or repairing any TSR system malfunction.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precaution for DAA System Service"
.
- System description for DAA: Refer to
DAS-24, "DAA : System Description"
- Handling precaution: Refer to
DAS-41, "Precautions for Drive Attention Alert"
DAA : Work Procedure
INFOID:0000000010927847
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precaution for DAA System Service"
.
- System description for DAA: Refer to
DAS-24, "DAA : System Description"
- Handling precaution: Refer to
DAS-41, "Precautions for Drive Attention Alert"
1.
CHECK DAA SYSTEM SETTING
1.
Start the engine.
2.
After starting the engine wait for 30 seconds or more.
TSR ON
Road sign
not detect-
ed
—
Road sign
detected
(except for
speed limit
signs)
—
This is an example. For details of dis-
played signs, refer to
Road sign
detected
(Speed limit
signs)
This is an example. For details of dis-
played signs, refer to
This is an example. For details of dis-
played signs, refer to
System status
Condition
Display on combination meter
Upper part
Middle part
JSOIA1612ZZ
JSOIA1613ZZ
JSOIA1614ZZ
JSOIA1615ZZ
DAS-96
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
3.
Check that the DAA system setting can be enabled/disabled on the combination meter.
4.
Turn OFF the ignition switch and wait for 5 seconds or more.
5.
Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR DAA
1.
Enable the setting of the DAA system on the combination meter.
2.
Check the DAA operation according to the following table.
>> INSPECTION END
Vehicle condition/ Driv-
er’s operation
Driver’s condi-
tion
Vehicle speed
(Approx.)
Action
Display on combination meter
DAA ON
—
0 km/h (0 MPH)
≤
Vehicle speed <
60 km/h (37
MPH)
—
—
Normal
More than 60 km/
h (37 MPH)
Level indicator: Blue
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст