Nissan X-Trail 32. Manual — part 1202
DIAGNOSIS SYSTEM (IPDM E/R)
EXL-265
< SYSTEM DESCRIPTION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
A/C RELAY
[Off/On]
Displays the status of the A/C relay judged by IPDM E/R.
COMP ECV STATUS
[OK/NG]
Displays the compressor malfunction diagnosis status judged by IPDM E/R.
VEHICLE SECURITY HORN
[Off/On]
NOTE:
The item is indicated, but not monitored.
BATTERY CURRENT SENSOR
[OK/NG]
Displays the battery current sensor malfunction diagnosis status judged by IPDM E/
R.
FRONT FOG LAMP
[Off/On]
Displays the fog lamp illumination control status of IPDM E/R.
COMP ECV CURRENT
[A]
Displays the electric current output to compressor judged by IPDM E/R.
BATTERY VOLTAGE
[V]
Displays the status of the battery voltage judged by IPDM E/R.
COOLING FAN DUTY
[%]
Displays the cooling fan output signal status of IPDM E/R.
HOOD SW (CAN)
[Open/Close/NG]
Displays the status of the hood switch judged by IPDM E/R.
FRONT WIPER
[STOP/HIGH/LOW/NG]
Displays the front wiper motor drive control status of IPDM E/R.
FR WIPER STOP POSITION
[ACTIVE P/STOP P]
Displays the status of the front wiper position status judged by IPDM E/R.
HEADLAMP (HI)
[Off/On]
Displays the headlamp (HI) illumination control status of IPDM E/R.
HEADLAMP (LO)
[Off/On]
Displays the headlamp (LO) illumination control status of IPDM E/R.
IGNITION RELAY STATUS
[Off/On]
Displays the ignition relay output status of IPDM E/R.
IGN RELAY MONITOR
[Off/On]
Displays the status of the ignition relay judged by IPDM E/R.
IGNITION POWER SUPPLY
[Off/On]
Displays the status of the ignition power supply judged by IPDM E/R.
INTERLOCK/PNP SW (CAN)
[Off/On]
Displays the status of the transmission range switch signal that IPDM transmits via
CAN communication.
NEUTRAL SWITCH (CAN)
[Off/On/NG]
Displays the status of the neutral position switch (M/T) signal that IPDM transmits via
CAN communication.
PUSH-BUTTON IGN SW (CAN)
[Off/On]
Displays the status of the ignition switch signal that IPDM transmits via CAN commu-
nication.
TAIL LAMP
[Off/On]
Displays the tail lamp illumination control status of IPDM E/R.
REVERSE SIGNAL (CAN)
[Off/On/NG]
Displays the status of the reverse switch (M/T) signal that IPDM transmits via CAN
communication.
ST&ST CONT RELAY STATUS
[Off/Off, ON/ST R On]
Displays the status of the start control relay and start motor relay status judged by
IPDM E/R.
STARTER MOTOR STATUS
[Off/On/L-TIME]
Displays the status of the starter motor judged by IPDM E/R.
STARTER RELAY (CAN)
[LOW/HIGH/NG]
Displays the status of the IPDM E/R transmits the starter control relay status signal
via CAN communication.
IPDM NOT SLEEP
[NO RDY/READY]
Displays the status of the IPDM E/R transmits the not sleep signal via CAN commu-
nication.
Monitor Item
[Unit]
Description
EXL-266
< SYSTEM DESCRIPTION >
[HALOGEN HEADLAMP]
DIAGNOSIS SYSTEM (IPDM E/R)
AFTER COOLING TIME
[No request/0.5min/1.0min/1.5min/
2.0min/2.5min/3.0min/3.5min/4min/5min/
6min/8min/10min/12min/14min/16min]
NOTE:
The item is indicated, but not monitored.
AFTER COOLING SPEED
[0%/25%/40%/55%/70%/78%/85%/
100%]
NOTE:
The item is indicated, but not monitored.
COOLING FAN TYPE
[RENAULT/NISSAN]
NOTE:
The item is indicated, but not monitored.
COMPRESSOR REQ 1
[Off/On]
Displays the status of the A/C compressor request signal received from ECM via CAN
communication.
VHCL SECRITY HORN REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
DTRL REQ
[Off/On]
Displays the status of the daytime running light request signal received from BCM via
CAN communication.
SLEEP/WAKE UP
[SLEEP/WAKEUP]
NOTE:
The item is indicated, but not monitored.
CLUTCH INTERLOCK SW
[Off/On/NG]
NOTE:
The item is indicated, but not monitored.
CRANKING ENABLE-TCM
[OK/NG]
Displays the status of the cranking enable signal received from TCM via CAN com-
munication.
CRANKING ENABLE-ECM
[OK/NG/STOP/No request]
Displays the status of the cranking enable signal received from ECM via CAN com-
munication.
CAN DIAGNOSIS
[OK/NG]
Displays the status of the CAN diagnosis signal received from BCM via CAN commu-
nication.
FRONT FOG LAMP REQ
[Off/On]
Displays the status of the front fog light request signal received from BCM via CAN
communication.
H/L WASHER REQ
[Off/On]
Displays the status of the headlamp washer request signal received from BCM via
CAN communication.
PASSING REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
HIGH BEAM REQ
[Off/On]
Displays the status of the high beam request signal received from BCM via CAN com-
munication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder signal received from BCM via CAN commu-
nication.
COOLING FAN REQ
[%]
Displays the status of the cooling fan speed request signal received from ECM via
CAN communication.
ENGINE STATUS
[STOP/IDLING/RUN]
Displays the status of the engine status signal received from ECM via CAN commu-
nication.
TURN SIGNAL REQ
[Off/LH/RH]
Displays the status of the turn indicator signal received from BCM via CAN commu-
nication.
FR WIPER REQ
[RETURN/STOP/NG/LOW/HIGH]
Displays the status of the front wiper request signal received from BCM via CAN com-
munication.
SHIFT POSITION
[OFF/P/R/N/D/S/L/B/1/2/3/4/5/6/7]
Displays the status of the shift position signal received from TCM via CAN communi-
cation.
LOW BEAM REQ
[Off/On]
Displays the status of the low beam request signal received from BCM via CAN com-
munication.
POSITION LIGHT REQ
[Off/On]
Displays the status of the position light request signal received from BCM via CAN
communication.
COMPRESSOR REQ 2
[Off/On]
Displays the status of the A/C ON signal received from A/C auto amp. via CAN com-
munication.
IGNITION SW
[Off/On/START/No request]
Displays the status of the ignition switch ON signal and starter control relay request
signal received from BCM via CAN communication.
Monitor Item
[Unit]
Description
DIAGNOSIS SYSTEM (IPDM E/R)
EXL-267
< SYSTEM DESCRIPTION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
VEHICLE SPEED (METER)
[km/h]
Displays the status of the A/C ON signal received from A/C auto amp. via CAN com-
munication.
BAT DISCHARGE COUNT
[—]
Monitor the cumulative discharge value of the battery.
NOTE:
When 65,000 or more is counted, replace the battery.
P LAMP CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the parking lamp circuit.
NOTE:
When the number of parking lamp circuit retries count is 20, this item counts 1.
NMB P LAMP CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
parking lamp circuit.
NOTE:
When the number of short circuits in the parking lamp circuit count is 5 and the igni-
tion switch OFF to ON operation is detected, this item counts 1.
NMB P LAMP CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the parking lamp circuit.
DTRL LH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the daytime running light (left) circuit.
NOTE:
When the number of daytime running light (left) circuit retries count is 20, this item
counts 1.
NMB DTRL LH CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
daytime running light (left) circuit.
NOTE:
When the number of short circuits in the daytime running light (left) circuit count is 5
and the ignition switch OFF to ON operation is detected, this item counts 1.
NMB DTRL LH CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the daytime running light (left) circuit.
DTRL RH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the daytime running light (right) circuit.
NOTE:
When the number of daytime running light (right) circuit retries count is 20, this item
counts 1.
NMB DTRL RH CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
daytime running light (right) circuit.
NOTE:
When the number of short circuits in the daytime running light (right) circuit count is
5 and the ignition switch OFF to ON operation is detected, this item counts 1.
NMB DTRL RH CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the daytime running light (right) circuit.
F FOG LH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the front fog lamp (left) circuit.
NOTE:
When the number of front fog lamp (left) circuit retries count is 20, this item counts 1.
NMB F FOG LH CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
front fog lamp (left) circuit.
NOTE:
When the number of short circuits in the front fog lamp (left) circuit count is 5 and the
ignition switch OFF to ON operation is detected, this item counts 1.
NMB F FOG LH CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the front fog lamp (left) circuit.
F FOG RH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the front fog lamp (right) circuit.
NOTE:
When the number of front fog lamp (right) circuit retries count is 20, this item counts 1.
Monitor Item
[Unit]
Description
EXL-268
< SYSTEM DESCRIPTION >
[HALOGEN HEADLAMP]
DIAGNOSIS SYSTEM (IPDM E/R)
NMB F FOG RH CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
front fog lamp (right) circuit.
NOTE:
When the number of short circuits in the front fog lamp (right) circuit count is 5 and
the ignition switch OFF to ON operation is detected, this item counts 1.
NMB F FOG RH CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the front fog lamp (right) circuit.
HL (HI) LH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the headlamp (HI) (left) circuit.
NOTE:
When the number of headlamp (HI) (left) circuit retries count is 20, this item counts 1.
NMB HL (HI) LH CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
headlamp (HI) (left) circuit.
NOTE:
When the number of short circuits in the headlamp (HI) (left) circuit count is 5 and the
ignition switch OFF to ON operation is detected, this item counts 1.
NMB HL (HI) LH CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the headlamp (HI) (left) circuit.
HL (HI) RH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the headlamp (HI) (right) circuit.
NOTE:
When the number of headlamp (HI) (right) circuit retries count is 20, this item counts
1.
NMB HL (HI) RH CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
headlamp (HI) (right) circuit.
NOTE:
When the number of short circuits in the headlamp (HI) (right) circuit count is 5 and
the ignition switch OFF to ON operation is detected, this item counts 1.
NMB HL (HI) RH CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the headlamp (HI) (right) circuit.
S/L CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the steering lock circuit.
NOTE:
When the number of steering lock circuit retries count is 20, this item counts 1.
NMB S/L CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
steering lock circuit.
NOTE:
When the number of short circuits in the steering lock circuit count is 5 and the ignition
switch OFF to ON operation is detected, this item counts 1.
NMB S/L CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the steering lock circuit.
HL (LO) LH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the headlamp (LO) (left) circuit.
NOTE:
When the number of headlamp (LO) (left) circuit retries count is 20, this item counts 1.
NMB HL (LO) LH CIRC RETRY
[0 – 20]
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the
headlamp (LO) (left) circuit.
NOTE:
When the number of short circuits in the headlamp (LO) (left) circuit count is 5 and
the ignition switch OFF to ON operation is detected, this item counts 1.
NMB HL (LO) LH CIRC SHORT
[0 – 5]
Monitor the number of times that the smart FET in IPDM E/R detects the over current
of the headlamp (LO) (left) circuit.
HL (LO) RH CIRC MALFUNCTN
[0 – 1]
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper
limit of the headlamp (LO) (right) circuit.
NOTE:
When the number of headlamp (LO) (right) circuit retries count is 20, this item counts
1.
Monitor Item
[Unit]
Description
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст