Nissan X-Trail 32. Manual — part 1183
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-189
< PERIODIC MAINTENANCE >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000010788880
PREPARATION BEFORE ADJUSTING
NOTE:
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Never remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
Aiming Adjustment Procedure
INFOID:0000000010788881
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Turn the front fog lamp ON.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4.
Adjust the cutoff line height
with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and
becomes 150 mm (5.90 in).
Front fog lamp light distribution on the screen
: DOWN
: UP
JMLIA4843ZZ
: Cutoff line
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
JPLIA0008ZZ
EXL-190
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
FRONT COMBINATION LAMP
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000010788882
REMOVAL
DISASSEMBLY
Front fender panel
Front combination lamp
: Vehicle front
: N·m (kg-m, in-lb)
JMLIA4944GB
FRONT COMBINATION LAMP
EXL-191
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000010788883
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-9, "Precautions for Removing Battery Terminal"
.
REMOVAL
1.
Remove front bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
2.
Remove front combination lamp mounting bolts and clip.
3.
Remove harness clip of front combination lamp bracket.
4.
Pull out front combination lamp forward the vehicle.
5.
Disconnect front combination lamp harness connectors and then remove front combination lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to the following.
• LHD MODELS: Refer to
EXL-184, "LHD MODELS : Description"
• RHD MODELS: Refer to
EXL-186, "RHD MODELS : Description"
.
Replacement
INFOID:0000000010788884
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-9, "Precautions for Removing Battery Terminal"
.
• After installing the bulb, install the bulb socket securely for watertightness.
Front combination lamp housing
Front combination lamp harness
Front turn signal lamp bulb socket
Front turn signal lamp bulb
Front combination lamp bracket
JMLIA4945ZZ
EXL-192
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
FRONT COMBINATION LAMP
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (HI)
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
front combination lamp as a set. Refer to
EXL-191, "Removal and Installation"
.
HEADLAMP BULB (LO)
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
front combination lamp as a set. Refer to
EXL-191, "Removal and Installation"
.
DAYTIME RUNNING LIGHT/ PARKING LAMP BULB
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
front combination lamp as a set. Refer to
EXL-191, "Removal and Installation"
.
FRONT TURN SIGNAL LAMP BULB
LH side
1.
Remove air duct 1. Refer to the following.
• MR20DD: Refer to
EM-31, "Removal and Installation"
.
• QR25DE: Refer to
EM-175, "Removal and Installation"
.
• R9M: Refer to
EM-308, "Removal and Installation"
.
2.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
3.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
RH side
1.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
2.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
Disassembly and Assembly
INFOID:0000000010788885
DISASSEMBLY
1.
Remove front combination lamp bracket fixing screws, and then remove front combination lamp bracket.
2.
Disconnect front combination lamp harness.
3.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
4.
Remove front turn signal lamp bulb from front turn signal lamp bulb socket.
ASSEMBLY
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installing the bulb, install the bulb socket securely watertightness.
• After installation, perform aiming adjustment. Refer to following.
- LHD MODELS: Refer to
EXL-184, "LHD MODELS : Description"
- RHD MODELS: Refer to
EXL-186, "RHD MODELS : Description"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст