Nissan X-Trail 32. Manual — part 1036
OIL PAN (LOWER)
EM-41
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Loosen mounting bolts in reverse order as shown in the figure.
b.
Insert seal cutter [SST: KV10111100] (A) between oil pan (upper)
and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surface.
• Since factory default liquid gasket has better adhesion
than conventional one, never pick the area forcibly with a
screw driver.
INSTALLATION
CAUTION:
Do not reuse O-rings or washers.
Note the following, and install in the reverse order of removal.
1.
Install oil pan (lower) with the following procedure:
a.
Use a scraper
to remove old liquid gasket from mating sur-
faces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surface when cleaning
off old liquid gasket.
: Engine front
PBIC3146J
JPBIA0276ZZ
PBIC3953E
EM-42
< REMOVAL AND INSTALLATION >
[MR20DD]
OIL PAN (LOWER)
b.
Apply a continuous bead of liquid gasket
with a tube presser
(commercial service tool) as shown in the figure.
Use Genuine Liquid Gasket (Three Bond 1217H) or equiva-
lent.
CAUTION:
Attaching should be done within 5 minutes after liquid gas-
ket application.
c.
Tighten bolts in numerical order as shown in the figure.
2.
Install drain plug.
3.
Install in the reverse order of removal after this steps.
NOTE:
Wait at least 30 minutes after oil pan is installed before pouring engine oil.
Inspection
INFOID:0000000010783697
INSPECTION AFTER REMOVAL
Clean oil strainer portion [part of the oil pan (upper)] if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leakage of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
: Oil pan (lower)
: Engine outside
PBIC3611J
: Engine front
PBIC3146J
HIGH PRESSURE FUEL PUMP AND FUEL HOSE
EM-43
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
HIGH PRESSURE FUEL PUMP AND FUEL HOSE
Exploded View
INFOID:0000000010783698
CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.
Removal and Installation
INFOID:0000000010783699
REMOVAL
WARNING:
EM-7, "Precaution for Handling High Pressure Fuel System"
when working on the
high pressure fuel system.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
High pressure fuel pump insulator
High pressure fuel pump
O-ring
High pressure fuel pump lifter
Fuel rail connector
Fuel tube
Bracket
Fuel pump connector protector
Fuel feed hose
To centralized under-floor piping
: Engine front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Should be lubricated with oil.
: Indicates that the parts is connected at points with same symbols in actual vehicle.
JSBIA4597GB
EM-44
< REMOVAL AND INSTALLATION >
[MR20DD]
HIGH PRESSURE FUEL PUMP AND FUEL HOSE
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
• To avoid the danger of being scalded, never drain engine coolant when engine is hot.
1.
Release fuel pressure. Refer to
2.
Remove fuel pump connector protector, and remove high pressure fuel pump insulator.
3.
Disconnect quick connector
with the following procedure.
a.
Disconnect fuel feed hose
from bracket hose clamp
.
b.
Disengage
and pull up
the pawl of the fuel feed hose con-
nector retainer
to disconnect the fuel feed hose from high
pressure fuel pump.
NOTE:
If the fuel feed hose is stuck, hold the fuel pipe by hand and dis-
connect it by pushing and pulling.
CAUTION:
• Keep parts away from heat source. Especially, be careful
when welding is performed around them.
• Never expose parts to battery electrolyte or other acids.
• Never bent or twist connection between quick connector
and fuel feed hose (with damper) during installation/
removal.
• Pull quick connector holding
.
• Never remove the retainer.
• Prepare a tray and waste beforehand as fuel leaks out.
• Never pull with lateral force applied. O-ring inside quick
connector may be damaged.
• To prevent damage to each joint and protect it from the
entry of foreign matter, cover the joint with plastic bag
or an equivalent.
4.
Remove intake manifold. Refer to
EM-33, "Removal and Installation"
5.
Remove fuel tube.
6.
Remove fuel rail connector.
JPBIA4376ZZ
Retainer color
: Red
JPBIA4377ZZ
JPBIA4378ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст