Nissan X-Trail 32. Manual — part 701
REAR PROPELLER SHAFT
DLN-215
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: C-CVJ-C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3.
Remove heat insulator
.
4.
Put matching marks
on propeller shaft flange yoke and trans-
fer companion flange.
CAUTION:
For matching mark, use paint. Never damage propeller shaft
flange yoke and transfer companion flange.
5.
Put matching marks
on propeller shaft flange yoke and elec-
tric controlled coupling.
CAUTION:
• For matching mark, use paint. Never damage propeller
shaft flange yoke and electric controlled coupling.
• If the tip of stud bolt of electric controlled coupling has a
paint mark, place a matching mark for identification of the
position of applicable stud bolt.
6.
Loosen mounting nuts of center bearing mounting bracket.
NOTE:
Tighten mounting nuts temporarily to prevent drop of propeller
shaft.
7.
Remove propeller shaft assembly fixing bolts, and separate pro-
peller shaft assembly from transfer companion flange.
JSDIA5324ZZ
JSDIA5328ZZ
JSDIA5325ZZ
JSDIA5326ZZ
JSDIA5329ZZ
DLN-216
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: C-CVJ-C]
REAR PROPELLER SHAFT
8.
Remove propeller shaft assembly fixing nuts, and separate pro-
peller shaft assembly from electric controlled coupling of final
drive.
9.
Remove center bearing mounting bracket mounting nuts.
10. Remove propeller shaft assembly.
11. Remove clips and then remove center bearing mounting bracket
(upper/lower).
12. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• For non-reusable parts, refer to
• For each tightening torque, refer to
.
• After removing propeller shaft, replace stud bolts on electric controlled coupling. Refer to
• Remove any moisture, oil, or foreign material from matching surface on transfer companion flange, electric
controlled coupling and propeller shaft flange.
• Install center bearing mounting bracket (upper) with its arrow mark
facing forward.
• Adjust position of center bearing mounting bracket (upper)
, cen-
ter bearing mounting bracket (lower)
sliding back and forth to
prevent play in thrust direction of center bearing insulator
. Install
center bearing mounting bracket (upper/lower) to vehicle.
• Center bearing mounting bracket fixing nuts must be tightened in
the order from left to right.
JSDIA5330ZZ
JSDIA4492ZZ
JSDIA4491ZZ
JSDIA5331ZZ
REAR PROPELLER SHAFT
DLN-217
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: C-CVJ-C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Align matching marks
to install propeller shaft flange yoke and
electric controlled coupling of final drive.
• Align matching marks
to install propeller shaft flange yoke and
transfer companion flange.
• If propeller shaft assembly, final drive assembly or electric controlled coupling has been replaced, connect
propeller shaft assembly and electric controlled coupling of final drive as follows:
- Install propeller shaft
while aligning its matching mark
of pro-
peller shaft with matching mark
on stud bolt of electric controlled
coupling
as close as possible.
CAUTION:
When replaced stud bolt, use the painted matching mark in
removal as a guide.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010822161
INSPECTION AFTER REMOVAL
Appearance
Check propeller shaft tube surface for dents or cracks. If malfunction is detected, replace propeller shaft
assembly.
Propeller Shaft Runout
Check propeller shaft runout at measuring points with a dial indica-
tor. If runout exceeds specifications, replace propeller shaft assem-
bly.
JSDIA5325ZZ
JSDIA5328ZZ
JSDIA5332ZZ
Propeller shaft runout
: Refer to
.
JSDIA0193ZZ
DLN-218
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: C-CVJ-C]
REAR PROPELLER SHAFT
• Propeller shaft runout measuring point (Point “ ”).
Journal Axial Play
As shown in the figure, while fixing yoke on one side, check axial
play of joint. If it is outside the standard, replace propeller shaft
assembly.
CAUTION:
Never disassemble joints.
Center Bearing
Check center bearing for noise and damage. If malfunction is detected, replace propeller shaft assembly.
CAUTION:
Never disassemble center bearing.
INSPECTION AFTER INSTALLATION
After assembly, perform a driving test to check propeller shaft vibration. If vibration occurred, separate propel-
ler shaft from final drive. Reinstall propeller shaft by changing the phase between electric controlled coupling
stud bolt and propeller shaft by the one bolt hole at a time. Then perform driving test and check propeller shaft
vibration again at each point.
: Front side
Dimension
MR20DD models
A
: 533.5 mm (21.00 in)
B
: 492.0 mm (19.37 in)
QR25DE models
A
: 540.5 mm (21.28 in)
B
: 492.0 mm (19.37 in)
R9M models
A
: 474.5 mm (18.68 in)
B
: 492.0 mm (19.37 in)
JPDID0001ZZ
Journal axial play
: Refer to
.
PDA0005D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст