Nissan X-Trail 32. Manual — part 2190
VTL-8
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
Rear (RHD models)
*: with rear ventilator models
CENTER VENTILATOR GRILLE
CENTER VENTILATOR GRILLE : Removal and Installation
INFOID:0000000010981803
REMOVAL
1.
Apply protective tapes (A) on instrument panel assembly to pro-
tect from damage.
JMIIA3377ZZ
A/C unit assembly
Rear ventilator duct 1
*
Rear floor duct 1 LH
Rear floor duct 2 LH
Rear ventilator duct 2
*
Console rear finisher
*
Rear ventilator grille
*
Rear floor duct 2 RH
Console switch finisher
*
Rear floor duct 1 RH
: Clip
: Pawl
JMIIA3341ZZ
DUCT AND GRILLE
VTL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
2.
Disengage fixing metal clips and pawls using remover tool (A), and then remove center ventilator grille
according to numerical order 1
→
3 indicated arrows as shown in the figure.
3.
Disconnect harness connector from center ventilator grille.
INSTALLATION
Install in the reverse order of removal.
SIDE VENTILATOR GRILLE
SIDE VENTILATOR GRILLE : Removal and Installation
INFOID:0000000010981804
REMOVAL
Driver Side
1.
Remove instrument mask (driver side). Refer to
IP-14, "Removal and Installation"
(LHD models) or
(RHD models).
2.
Apply protective tape (A) on instrument panel assembly to pro-
tect from damage.
3.
Disengage fixing pawls using a remover tool (A), and then
remove side ventilator grille (finisher portion)
.
: Pawl
: Metal clip
JMIIA3417ZZ
JMIIA3343ZZ
: Pawl
JMIIA3374ZZ
VTL-10
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
4.
Disengage fixing metal clips, and then remove side ventilator
grille (case portion) according to numerical order 1
→
2 indicated
by arrows as shown in the figure.
Passenger Side
1.
Remove instrument mask (passenger side). Refer to
IP-14, "Removal and Installation"
(LHD models) or
IP-41, "Removal and Installation"
(RHD models).
2.
Apply protective tape (A) on instrument panel assembly to pro-
tect from damage.
3.
Disengage fixing pawls using a remover tool (A), and then
remove side ventilator grille (finisher portion)
.
4.
Disengage fixing metal clips, and then remove side ventilator
grille (case portion) by arrows as shown in the figure.
INSTALLATION
Install in the reverse order of removal.
CENTER VENTILATOR DUCT
CENTER VENTILATOR DUCT : Removal and Installation
INFOID:0000000010981805
REMOVAL
: Metal clip
JMIIA3375ZZ
JMIIA3342ZZ
: Pawl
JMIIA3378ZZ
: Metal clip
JMIIA3379ZZ
DUCT AND GRILLE
VTL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
1.
Remove instrument panel assembly. Refer to
IP-14, "Removal and Installation"
(RHD models).
2.
Remove front defroster nozzle. Refer to
VTL-11, "FRONT DEFROSTER NOZZLE : Removal and Installa-
3.
Remove fixing screws
, and then remove center ventilator duct assembly from instrument panel assem-
bly.
INSTALLATION
Install in the reverse order of removal.
FRONT DEFROSTER NOZZLE
FRONT DEFROSTER NOZZLE : Removal and Installation
INFOID:0000000010981806
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-14, "Removal and Installation"
(RHD models).
2.
Remove fixing screws
, and then remove center defroster noz-
zle from instrument panel assembly.
INSTALLATION
Install in the reverse order of removal.
SIDE DEFROSTER NOZZLE
SIDE DEFROSTER NOZZLE : Removal and Installation
INFOID:0000000010981807
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-14, "Removal and Installation"
(RHD models).
JMIIA3410ZZ
JMIIA3380ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст