Nissan X-Trail 32. Manual — part 1718
PG-126
< BASIC INSPECTION >
BATTERY INSPECTION
3.
Read load tester voltage when specified discharging current flows through battery for 15 seconds.
Is the voltage 9.6 V or more?
YES
>> Ready for use.
NO
>> GO TO 7.
7.
QUICK CHARGE
1.
Perform quick charge. Time required: 45 min. Refer to
.
2.
Perform capacity test.
>> GO TO 13.
8.
QUICK CHARGE
1.
Perform quick charge. Refer to
.
2.
Perform capacity test.
>> GO TO 9.
9.
CAPACITY TEST
1.
Test using load tester.
2.
Check battery type and determine the specified current using the table.
Discharging Current (Load Tester)
46B24L/R
135
55B24L/R
55B24L(S)
50D23L/R
150
55D23L/R
180
80D23L/R
195
65D26L/R
80D26L/R
75D31L/R
210
95D31L/R
240
115D31L/R
025 [YUASA type code]
027 [YUASA type code]
285
110D26L/R
300
95E41L/R
067 [YUASA type code]
325
130E41L/R
330
096 [YUASA type code]
375
Type
Current (A)
Type
Current (A)
28B19L/R
90
34B19L/R
99
46B24L/R
135
55B24L/R
55B24L(S)
50D23L/R
150
55D23L/R
180
PG
BATTERY INSPECTION
PG-127
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
3.
Read load tester voltage when specified discharging current flows through battery for 15 seconds.
Is the voltage 9.6 V or more?
YES
>> Ready for use.
NO
>> GO TO 10.
10.
CHECKING SPECIFIC GRAVITY
1.
Check specific gravity. Refer to
PG-121, "EXCEPT FOR R9M : How to Handle Battery"
.
2.
Perform recharge. Refer to
NOTE:
If battery temperature rises above 55
°
C (131
°
F), stop charging. Always charge battery when its tempera-
ture is below 55
°
C (131
°
F).
3.
Perform capacity test.
>> GO TO 13.
11.
STANDARD CHARGE
NOTE:
“STANDARD CHARGE” is recommended if the vehicle is in storage after charging.
1.
Perform standard charge. Refer to
2.
Perform capacity test.
>> GO TO 13.
12.
SLOW CHARGE
1.
Perform slow charge. Refer to
2.
Perform capacity test.
>> GO TO 13.
13.
CAPACITY TEST
1.
Test using load tester.
2.
Check battery type and determine the specified current using the table.
Discharging Current (Load Tester)
80D23L/R
195
65D26L/R
80D26L/R
75D31L/R
210
95D31L/R
240
115D31L/R
025 [YUASA type code]
027 [YUASA type code]
285
110D26L/R
300
95E41L/R
067 [YUASA type code]
325
130E41L/R
330
096 [YUASA type code]
375
Type
Current (A)
Type
Current (A)
28B19L/R
90
34B19L/R
99
PG-128
< BASIC INSPECTION >
BATTERY INSPECTION
3.
Read load tester voltage when specified discharging current flows through battery for 15 seconds.
Is the voltage 9.6 V or more?
YES
>> Ready for use.
NO
>> Replace battery.
46B24L/R
135
55B24L/R
55B24L(S)
50D23L/R
150
55D23L/R
180
80D23L/R
195
65D26L/R
80D26L/R
75D31L/R
210
95D31L/R
240
115D31L/R
025 [YUASA type code]
027 [YUASA type code]
285
110D26L/R
300
95E41L/R
067 [YUASA type code]
325
130E41L/R
330
096 [YUASA type code]
375
Type
Current (A)
PG
FUSE INSPECTION
PG-129
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FUSE INSPECTION
How To Check
INFOID:0000000010709231
• If fuse is blown, be sure to eliminate cause of malfunction before
installing new fuse.
• Use fuse of specified rating. Never use fuse of more than specified
rating.
• Do not partially install fuse; always insert it into fuse holder prop-
erly.
• Remove fuse for “ELECTRICAL PARTS (BAT)” if vehicle is not
used for a long period of time.
EXTENDED STORAGE FUSE SWITCH (IF EQUIPPED)
The following switch may be mounted on the fuse block (Junction Box) for transportation and storage.
Remove the extended storage fuse switch if it causes the interference when checking fuses.
How To Extended Storage Fuse Switch ON/OFF
CAUTION:
• Turn the ignition switch OFF when operating the extended storage fuse switch.
• Under normal conditions, keep the extended storage fuse switch in ON state. Never operate the
extended storage fuse switch except when necessary.
CEL083
Extended storage fuse switch
Type A
Type B
Type C
JSMIA0793ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст