Nissan X-Trail 32. Manual — part 1798
SE-40
< REMOVAL AND INSTALLATION >
FRONT SEAT
MANUAL SEAT
JMJIB0185GB
Seatback silencer
Headrest
Headrest holder (lock)
Headrest holder (free)
Seatback frame
Seatback suspension
Side air bag module
Reclining knob
Snap ring
Seat cushion outside finisher outer
side
Seat cushion inside finisher outer
side rear
Seat cushion inside finisher outer
side front
Seat slide cover
End cap
Lifter knob
Seat cushion lowside finisher outer
side
Seat harness
Rivet
Lifter lever
Bracket
Connector bracket
FRONT SEAT
SE-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
*1
: Never disassemble with heater seat.
*2
: Never disassemble passenger seat side with occupant sensor.
Removal and Installation
INFOID:0000000010713133
WARNING:
• Before servicing, push ignition switch OFF, disconnect battery negative terminal and then wait for at
least 3 minutes (discharges electricity held in the additional power supply circuit of the air bag diag-
nosis sensor unit).
• Never use air tools or electric tools for servicing (prevents the air bag diagnosis sensor unit from
activating unexpectedly due to vibration).
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
REMOVAL
1.
Remove headrest.
2.
Remove seat fixing bolts.
3.
Disengage seat cushion lower harness connector, and harness fixing clips.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing, tighten fixing bolts according to the numeri-
cal order 1
→
4 as shown in the figure, starting from front inner
fixing bolt.
• After work is completed, check that on system malfunction is detected by air bag warning lamp.
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000010713134
CAUTION:
When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
DISASSEMBLY
Seat cushion suspension
Seat cushion frame
Seat cushion lowside finisher inner
side
Seat cushion inside finisher inner
side rear
Seat cushion inside finisher inner
side front
Seat cushion outside finisher inner
side
Seat cushion silencer
Seat cushion pad
*1
*2
Seat cushion trim
*1
*2
Seatback pad
*1
Seatback trim
*1
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMJIA9601ZZ
SE-42
< REMOVAL AND INSTALLATION >
FRONT SEAT
1.
Disengage seatback fixing retainers
.
2.
Disengage side air bag harness connector
and harness clips.
3.
Disengage side air bag harness fixing magic fastener
, and
seatback trim fixing retainer
.
4.
Open the seatback fasteners
.
5.
Remove lumber support protector fixing screws
, and then
remove lumber support protector (if equipped).
JMJIA9572ZZ
: Clip
JMJIA9573ZZ
JMJIA9574ZZ
JMJIA9575ZZ
JMJIB0140ZZ
FRONT SEAT
SE-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
6.
Remove side air bag module.
a.
Disengage side air bag harness clip, and then remove side air
bag module fixing nuts
.
b.
Pull out side air bag module
form seatback trim inner cloth
(reinforcement cloth)
, while rotated seatback pad
.
CAUTION:
• Check the mounting condition for at assembly.
• Never damage the seatback trim and seatback trim inner cloth (reinforcement cloth).
• Note the following when handling the removed side air bag module.
- To prevent accidental explosion, never disassemble the side air bag module.
- When disposing of the side air bag module, refer to
SR-42, "SIDE AIR BAG MODULE : Deploy-
SR-43, "SIDE AIR BAG MODULE : Disposal"
.
- To prevent damage to the parts, never impact the side air
bag module. Replace the side air bag module if it is
dropped or sustains an impact.
- Always place the side air bag module alone with deploy-
ing direction facing upward.
- Never expose the air bag module to temperatures exceeding 90
°
C (194
°
F).
- Never allow oil, grease, detergent, or water to come in contact with the side air bag module.
: Clip
JMJIA9576ZZ
JMJIA9577ZZ
PHIA1183J
: Deploying direction
JMHIA1748ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст