Nissan X-Trail 32. Manual — part 1544
LU-12
< PERIODIC MAINTENANCE >
[MR20DD]
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000010783292
REMOVAL
• Using oil filter wrench [SST: KV10115801](A), remove oil filter
.
CAUTION:
• Oil filter is provided with relief valve. Use Genuine NISSAN
Oil Filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any engine
oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter installation surface.
2.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn
. Or tighten to specification.
Inspection
INFOID:0000000010783293
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
: Engine front
JSBIA4402ZZ
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
OIL COOLER
LU-13
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000010783294
M/T models
JPBIA6894GB
Clamp
Water hose
Oil filter
Connector bolt
Oil cooler
Water hose
To thermostat housing
To thermostat housing
Comply with the assembly procedure
when tightening. Refer to
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
LU-14
< REMOVAL AND INSTALLATION >
[MR20DD]
OIL COOLER
CVT models
Removal and Installation
INFOID:0000000010783295
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
1.
Drain engine coolant from radiator and cylinder block. Refer to
NOTE:
Perform this step when removing water hoses.
2.
Using oil filter wrench [SST: KV10115801], remove oil filter. Refer to
LU-12, "Removal and Installation"
.
3.
Disconnect water hoses from oil cooler.
• When removing oil cooler only, pinching water hoses near oil cooler to prevent engine coolant from spill-
ing out.
• Remaining engine coolant in piping will come out. Use a tray to collect it.
CAUTION:
Perform this step when the engine is cold.
4.
Remove connector bolt, and remove oil cooler.
INSTALLATION
Installation is the reverse order of removal.
JPBIA6895GB
Clamp
Water hose
Oil filter
Connector bolt
Oil cooler
Water hose
Heater thermostat
Water hose
To thermostat housing
To thermostat housing
Comply with the assembly procedure
when tightening. Refer to
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
OIL COOLER
LU-15
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
• Tighten the connector bolt
after aligning the stopper
on the oil
pan (upper) side with protrusion of oil cooler
.
Inspection
INFOID:0000000010783296
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
2.
Start the engine, and check that there is no leakage of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
: Engine front
JPBIA6907ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст