Nissan X-Trail 32. Manual — part 1902
SN-64
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
B2723-14 CORNER SENSOR [RR]
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK CORNER SENSOR REAR RH GROUND CIRCUIT
Check the continuity between sonar control unit harness connector and corner sensor rear RH harness con-
nector.
Is the inspection result normal?
YES
>> Replace corner sensor rear RH. Refer to
SN-114, "REAR : Removal and Installation"
NO
>> Repair or replace malfunctioning parts.
Terminals
Continuity
(+)
(
−
)
Sonar control unit
Connector
Terminal
B101
10
Ground
Not existed
Sonar control unit
Corner sensor rear RH
Continuity
Connector
Terminal
Connector
Terminal
B101
14
B123
1
Existed
SN
B2723-55 CORNER SENSOR [RR]
SN-65
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2723-55 CORNER SENSOR [RR]
DTC Description
INFOID:0000000010735580
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Corner sensor rear RH
• Control unit setting of sonar control unit is incomplete
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B2723-55 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010735581
1.
PERFORM CONFIGURATION OF SONAR CONTROL UNIT
Perform configuration of sonar control unit. Refer to
SN-41, "CONFIGURATION (SONAR CONTROL UNIT) :
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform DTC confirmation procedure again. Refer to
Is DTC B2723-55 detected again?
YES
>> Replace corner sensor rear RH. Refer to
SN-114, "REAR : Removal and Installation"
NO
>> INSPECTION END.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B2723-55
CORNER SENSOR [RR]
(Corner sensor rear-right)
CONFIG ERROR
(Configuration er-
ror)
Control unit setting of sonar control unit is incomplete or is not set
normally.
SN-66
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
B2723-92 CORNER SENSOR [RR]
B2723-92 CORNER SENSOR [RR]
DTC Description
INFOID:0000000010735582
DTC DETECTION LOGIC
POSSIBLE CAUSE
Corner sensor rear RH
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B2723-92 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010735583
1.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
With CONSULT
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC confirmation procedure again. Refer to
Is DTC B2723-92 detected again?
YES
>> Replace corner sensor rear RH. Refer to
SN-114, "REAR : Removal and Installation"
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B2723-92
CORNER SENSOR [RR]
(Corner sensor rear-right)
SENSOR
(Sensor)
Corner sensor rear RH malfunction is detected when ignition switch
is turned ON.
SN
B2724-55 SONAR CONTROL UNIT
SN-67
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2724-55 SONAR CONTROL UNIT
DTC Description
INFOID:0000000010735584
DTC DETECTION LOGIC
POSSIBLE CAUSE
Control unit setting of sonar control unit is incomplete
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B2724-55 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010735585
1.
PERFORM CONFIGURATION OF SONAR CONTROL UNIT
Perform configuration of sonar control unit. Refer to
SN-41, "CONFIGURATION (SONAR CONTROL UNIT) :
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform DTC confirmation procedure again. Refer to
Is DTC B2724-55 detected again?
YES
>> Replace sonar control unit. Refer to
SN-111, "Removal and Installation"
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B2724-55
SONAR CONTROL UNIT
(Sonar control unit)
Control unit setting of sonar control unit is incomplete or is not set
normally.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст