Nissan X-Trail 32. Manual — part 2230
SYSTEM
WW-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
HEADLAMP WASHER SYSTEM : Circuit Diagram
INFOID:0000000011014533
JMLIA5504GB
WW-28
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010957675
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: This item is displayed, but not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Exterior lamp
HEAD LAMP
×
×
×
Interior room lamp control
INT LAMP
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
—
AIR CONDITONER*
×
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
Interior room lamp battery saver
BATTERY SAVER
×
Back door open
TRUNK
×
Vehicle security
THEFT ALM
×
×
RAP
RETAINED PWR
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
Signal buffer system
SIGNAL BUFFER
×
×
DIAGNOSIS SYSTEM (BCM)
WW-29
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER
WIPER : CONSULT Function - WIPER
INFOID:0000000010785422
WORK SUPPORT
*
1
: For models without light & rain sensor
*
2
: For models with light & rain sensor
*
3
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT screen item
Indication/Unit
Description
BATTERY VOLTAGE
V
Battery voltage of the moment a particular DTC is detected.
VEHICLE SPEED
km/h
Vehicle speed of the moment a particular DTC is detected.
EXTERNAL TEMP
°
C
External temperature of the moment a particular DTC is detected
VEHICLE COND
—
NOTE:
This item is displayed, but cannot be use this item.
DOOR LOCK STATUS
—
NOTE:
This item is displayed, but cannot be use this item.
POWER SUPPLY
COUNTER
min
Displays the cumulative time from the time that the battery terminal is connected.
Service item
Setting item
Description
WIPER SPEED SET-
TING*
1
On*
3
Linked with vehicle speed
(Front wiper intermittent time linked with the vehicle speed and
wiper volume dial position.)
The setting of front wiper
INT operation can be
changed.
Off
Not linked with vehicle speed
(Front wiper intermittent time linked with the wiper volume dial
position.)
RAIN SENSOR*
2
On*
3
Linked with light & rain sensor
(Front wiper intermittent time linked with the light & rain sensor,
vehicle speed, and wiper volume dial position)
The setting of front wiper
AUTO operation can be
changed
Off
Not linked with light & rain sensor
(Front wiper intermittent time linked with the vehicle speed and
wiper volume dial position)
FR RR DRIP
On*
3
Front wiper drop wipe and rear wiper drop wipe operation ON
The setting of drop wipe
operation can be
changed
Off
Front wiper drop wipe and rear wiper drop wipe operation OFF
REAR WIPER LINK
WITH REVERSE
SETTING
On
Rear wiper operation linked with reverse ON
The setting of rear wiper
operation linked with re-
verse can be changed
Off*
3
Rear wiper operation linked with reverse OFF
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch.
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication.
WW-30
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*: For models without headlamp washer switch, this item is indicated but is not used.
ACTIVE TEST
*: For models without headlamp washer, this item is indicated but is not used.
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function.
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function.
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function.
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Displays the status of the rear wiper stop position signal received from rear wiper motor.
H/L WSR SW*
[Off/On]
Status of headlamp washer switch judged by BCM.
RAIN SENSOR
[OFF/LOW/HIGH/SPLASH/NG]
Request signal from light & rain sensor detected by BCM is displayed.
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Operates the front wiper HI operation.
Lo
Operates the front wiper LO operation.
INT
Operates the front wiper INT/AUTO operation.
Off
Stops the front wiper operation.
RR WIPER
On
Operates the rear wiper operation.
Off
Stops the rear wiper operation.
HEADLAMP WASHER*
On
Operates the headlamp washer operation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст