Nissan X-Trail 32. Manual — part 568
FRONT DOOR LOCK
DLK-613
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7.
Disengage rod holder
and disconnect key rod
from door lock assembly
according to the numerical
order 1
→
2 indicated by arrows as shown in the figure (driver side).
8.
Remove door side grommet
, and then loosen TORX bolt
from grommet hole.
9.
Remove outside handle escutcheon
while pulling outside
handle grip
according to the numerical order 1
→
2 indicated
by arrows as shown in the figure.
: Vehicle front
JMKIB3523ZZ
JMKIB3524ZZ
JMKIA8374ZZ
DLK-614
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DOOR LOCK
10. Slide outside handle grip
toward rear of vehicle and remove it
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
11. Remove front gasket
and rear gasket
.
12. Slide outside handle bracket toward rear of vehicle and remove
it.
13. Disconnect outside handle cable
from outside handle bracket
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• When installing key rod, rotate key rod holder until a click is felt.
• After installation, check door lock. Refer to
DLK-611, "DOOR LOCK : Inspection"
JMKIA0524ZZ
: Pawl
: Vehicle front
JMKIB1627ZZ
: Vehicle front
JMKIB2034ZZ
JMKIB3525ZZ
REAR DOOR LOCK
DLK-615
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000010728158
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010728159
REMOVAL
1.
Disconnect lock knob cable and inside handle cable from inside handle. Refer to
DLE : Removal and Installation"
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly connector.
4.
Remove door lock assembly TORX bolts, and then remove door lock assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
Outside handle escutcheon
Rear gasket
TORX bolt
Door lock assembly
Inside handle
Outside handle bracket
Front gasket
Outside handle grip
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3526GB
DLK-616
< REMOVAL AND INSTALLATION >
[TYPE 2]
REAR DOOR LOCK
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• After installation, check door lock. Refer to
DLK-616, "DOOR LOCK : Inspection"
.
DOOR LOCK : Inspection
INFOID:0000000010728160
1.
After opening and closing the door, check that door is fixed to the vehicle body normally.
2.
Check the lock/unlock operation of door lock.
3.
Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010728161
REMOVAL
1.
Remove rear door finisher. Refer to
INT-19, "Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle
from door panel
while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
4.
Disengage lock knob cable
and inside handle cable
from
inside handle
according to the numerical order 1
→
4 indicated
by arrows as shown in the figure.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check door lock. Refer to
DLK-616, "DOOR LOCK : Inspection"
OUTSIDE HANDLE
: Body grease
JMKIA8534ZZ
: Pawl
JMKIB3527ZZ
JMKIB3521ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст