Nissan X-Trail 32. Manual — part 666
TRANSFER OIL
DLN-75
< PERIODIC MAINTENANCE >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
QR25DE : Inspection
INFOID:0000000011001971
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug
and gasket. Then check that oil is filled up
from mounting hole for filler plug.
CAUTION:
Turn the ignition switch OFF while checking oil level.
• Oil level should be level with bottom of filler plug mounting
hole. Add transfer oil if necessary. Refer to
2.
Set a new gasket on filler plug and install it on transfer assem-
bly. Refer to
.
CAUTION:
Never reuse gasket.
QR25DE : Draining
INFOID:0000000011001972
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Turn the ignition switch OFF.
3.
Remove drain plug
and gasket.
4.
Drain transfer oil.
5.
Before installing drain plug, set a new gasket. Install drain plug
to transfer assembly and tighten to the specified torque. Refer to
.
CAUTION:
Never reuse gasket.
QR25DE : Refilling
INFOID:0000000011001973
1.
Remove filler plug
and gasket. Then fill with new transfer oil
until oil level reaches the specified level near filler plug mounting
hole.
2.
Leave the vehicle for 3 minutes, and check the oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug to transfer assembly and tighten to the spec-
ified torque. Refer to
.
CAUTION:
Never reuse gasket.
: Oil level
: Vehicle front
ALDIA0503ZZ
: Vehicle front
AWDIA1153ZZ
: Oil level
: Vehicle front
Recommended
oil and capacity
.
ALDIA0503ZZ
DLN-76
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
4WD CONTROL UNIT
REMOVAL AND INSTALLATION
4WD CONTROL UNIT
Exploded View
INFOID:0000000010992028
Removal and Installation
INFOID:0000000010992029
REMOVAL
1.
Turn the ignition switch OFF.
2.
Remove luggage side lower finisher LH. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER :
.
3.
Disconnect 4WD control unit harness connector.
4.
Remove 4WD control unit mounting nuts
and remove 4WD
control unit
.
NOTE:
4WD control unit is located on the back side of the rear wheel
house outer panel LH.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform adjustment after installation. Refer to
.
Adjustment
INFOID:0000000010992030
ADJUSTMENT AFTER INSTALLATION
When replaced 4WD control unit, perform writing unit characteristics. Refer to
.
4WD control unit
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA5368GB
: Vehicle front
AWDIA1154ZZ
4WD MODE SWITCH
DLN-77
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD MODE SWITCH
Exploded View
INFOID:0000000010992031
Removal and Installation
INFOID:0000000010992032
REMOVAL
1.
Remove console switch panel from center console assembly. Refer to
IP-25, "Removal and Installation"
IP-52, "Removal and Installation"
(RHD models).
2.
Disconnect 4WD mode switch harness connector.
3.
Remove 4WD mode switch from console switch panel.
INSTALLATION
Install in the reverse order of removal.
4WD mode switch
Console switch panel
JSDIA5457ZZ
DLN-78
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
TRANSFER COVER OIL SEAL
TRANSFER COVER OIL SEAL
MR20DD
MR20DD : Exploded View
INFOID:0000000010992033
MR20DD : Removal and Installation
INFOID:0000000010992034
REMOVAL
1.
Drain the transfer oil. Refer to
.
2.
Remove front drive shaft (right side). Refer to
FAX-101, "MR20DD : Removal and Installation"
CAUTION:
Oil may leak from the opening. Use cap and/or plug to prevent leakage.
3.
Remove transfer cover oil seal (outer/inner), using oil seal remover (commercial service tool).
CAUTION:
Never damage transfer cover.
INSTALLATION
1.
Using drift (commercial service tool), install transfer cover oil
seal (outer/inner) with the directions below.
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and transfer oil onto the circumference of oil seal.
2.
Install front drive shaft (right side). Refer to
FAX-101, "MR20DD : Removal and Installation"
3.
Refill the transfer oil to transfer assembly. Refer to
Transfer assembly
Transfer cover oil seal (inner)
Transfer cover oil seal (outer)
Oil seal lip
: Always replace after every disassembly.
: Apply transfer oil.
: Apply multi-purpose grease.
JSDIA5360ZZ
A
: Installation dimension for transfer cover oil seal (inner)
B
: Installation dimension for transfer cover oil seal (outer)
A
: 10.3 +0.6/-0 mm (0.406 +0.024/-0 in)
B
: 0 +0.6/-0 mm (0 +0.024/-0 in)
JSDIA3993ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст