Nissan X-Trail 32. Manual — part 1952
SR-22
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
• Fix the driver air bag module harness to the harness fixing
hook .
• Press driver air bag module upper
until it snaps into place
with a clicking sound.
• Press driver air bag module lower
until it snaps into place
with a clicking sound.
• Check that horn does not sound when driver air bag module is not pressed.
• Never damage the harness while installing.
• After installation is complete, perform self-diagnosis using CONSULT or air bag warning lamp, if the
system is normal and
″
PAST
″
of
″
Self Diagnostic Result
″
is indicated, always perform
″
ERASE
″
of
″
Self Diagnostic Result
″
using CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA2735ZZ
JMHIA2640ZZ
JMHIA2641ZZ
SPIRAL CABLE
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Exploded View
INFOID:0000000010927726
Removal and Installation
INFOID:0000000010927727
WARNING:
Always observe the following items for preventing accidental activation.
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more (discharges electricity held in the additional power supply circuit of the air bag diagno-
sis sensor unit).
REMOVAL
1.
Remove driver air bag module. Refer to
SR-19, "Removal and Installation"
.
2.
Remove steering wheel. Refer to
ST-12, "Removal and Installation"
.
3.
Remove steering column upper cover and steering column lower cover.
• For australia: Refer to
IP-41, "Removal and Installation"
• For china: Refer to
IP-14, "Removal and Installation"
.
Steering column assembly
Steering wheel
Driver air bag module
Spiral cable
Steering angle sensor
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA2875GB
SR-24
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
4.
Disconnect spiral cable body side harness connectors
.
5.
Remove spiral cable fixing screws
, and then remove spiral
cable.
CAUTION:
• To prevent damage to the spiral cable, never impact it.
• Replace the spiral cable if it is dropped or sustains an
impact.
• To prevent damage to the parts, never disassemble the spiral cable.
• To prevent damage to the parts, never apply lubricant to the spiral cable.
• To prevent damage to the parts, never allow oil, grease, detergent, or water to come in contact
with the spiral cable.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
JMHIA2876ZZ
JMHIA2877ZZ
JMHIA0009ZZ
SPIRAL CABLE
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as per the following.
• Carefully turn the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the mark
on which the stopper insertion
holes are in the same position.
- Never over turn the spiral cable or go beyond the number of
turns required. (This causes the cable to snap)
- The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Adjust the spiral cable locating pin
to the steering wheel
locating pin hole
.
• After installation is complete, perform self-diagnosis using CONSULT or air bag warning lamp, if the
system is normal and
″
PAST
″
of
″
Self Diagnostic Result
″
is indicated, always perform
″
ERASE
″
of
″
Self Diagnostic Result
″
using CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA2878ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст