Nissan X-Trail 32. Manual — part 1039
FUEL INJECTOR AND FUEL TUBE
EM-53
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Inspection
INFOID:0000000010783703
INSPECTION AFTER INSTALLATION
Check on Fuel Leakage
1.
Turn ignition switch “ON” (with the engine stopped). With fuel pressure applied to fuel piping, check there
are no fuel leakage at connection points.
NOTE:
Use mirrors for checking at points out of clear sight.
2.
Start the engine. With engine speed increased, check again that there are no fuel leakage at connection
points.
CAUTION:
Never touch the engine immediately after stopped, as the engine becomes extremely hot.
EM-54
< REMOVAL AND INSTALLATION >
[MR20DD]
IGNITION COIL, SPARK PLUG AND ROCKER COVER
IGNITION COIL, SPARK PLUG AND ROCKER COVER
Exploded View
INFOID:0000000010783704
Removal and Installation
INFOID:0000000010783705
REMOVAL
1.
Remove intake manifold. Refer to
2.
Remove PCV valve and PCV hose, if necessary.
3.
Remove ignition coil.
Ignition coil
Spark plug
Rocker cover
Rocker cover gasket
Oil filler cap
PCV valve
O-ring
Comply with the installation proce-
dure when tightening. Refer to
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPBIA6815GB
IGNITION COIL, SPARK PLUG AND ROCKER COVER
EM-55
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAUTION:
• Never drop or shock ignition coil.
• Never disassemble ignition coil.
4.
Remove rocker cover.
• Loosen bolts in the order from 7 to 1 shown in the figure.
5.
Remove rocker cover gasket from rocker cover.
6.
Use scraper to remove all traces of liquid gasket from camshaft bracket.
CAUTION:
Never scratch or damage the mating surface when cleaning off old liquid gasket.
INSTALLATION
CAUTION:
Do not reuse O-ring.
1.
Install the rocker cover gasket to rocker cover.
CAUTION:
Check the gasket is not dropped.
2.
Install rocker cover.
• Tighten bolts in two steps separately in the order from 1 to 7 as
shown in the figure.
3.
Install in the reverse order of removal, for the rest of parts.
JPBIA6816ZZ
1st step
: 1.96 N·m (0.20 kg-m, 17 in-lb)
2nd step
: 8.33 N·m (0.85 kg-m, 74 in-lb)
JPBIA6816ZZ
EM-56
< UNIT REMOVAL AND INSTALLATION >
[MR20DD]
ENGINE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Exploded View
INFOID:0000000010783706
Removal and Installation
INFOID:0000000010783707
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• Attach proper slingers and bolts described in PARTS CATALOG if engine slingers are not equipped.
CAUTION:
Engine mounting insulator (RH)
Rear torque rod bracket
Rear torque rod
Engine mounting bracket (LH)
Stud bolt
Engine mounting bracket support
(LH)
Engine mounting insulator (LH)
4WD models
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPBIA6801GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст