Nissan X-Trail 32. Manual — part 630
KEY REMINDER FUNCTION DOES NOT OPERATE
DLK-861
< SYMPTOM DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY REMINDER FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000010755076
1.
CHECK KEY SWITCH
Check key switch.
Refer to
DLK-845, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DRIVER SIDE DOOR SWITCH
Check driver side door switch.
Refer to
DLK-842, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DLK-862
< SYMPTOM DIAGNOSIS >
[TYPE 4]
REMINDER FUNCTION DOES NOT OPERATE
REMINDER FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000010755077
1.
CHECK DTC WITH BCM AND COMBINATION METER
Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Refer to
NO-2
>> Refer to
. (Combination meter)
2.
CHECK HAZARD WARNING LAMP
Check hazard warning lamp.
Refer to
DLK-844, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
UNLOCK LINK FUNCTION DOES NOT OPERATE
DLK-863
< SYMPTOM DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
UNLOCK LINK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000010780996
1.
CHECK DRIVER SIDE OR PASSENGER SIDE DOOR SWITCH
Check driver side or passenger side door switch.
Refer to
DLK-842, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DLK-864
< SYMPTOM DIAGNOSIS >
[TYPE 4]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work Flow
INFOID:0000000010755080
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of
the customer's comments; refer to
DLK-868, "Diagnostic Worksheet"
. This information is necessary to dupli-
cate the conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain
all the facts and conditions that exist when the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer is
concerned about. This can be accomplished by a test drive with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
• Squeak – (Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces
= higher pitch noise/softer surfaces = lower pitch noises/edge to surface = chirping
• Creak – (Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch depen-
dent on materials/often brought on by activity.
• Rattle – (Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
• Knock – (Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
• Tick – (Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
• Thump – (Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
• Buzz – (Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
• Often the degree of acceptable noise level will vary depending upon the person. A noise that you may judge
as acceptable may be very irritating to the customer.
• Weather conditions, especially humidity and temperature, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
SBT842
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст