Nissan X-Trail 32. Manual — part 446
B2416 TOUCH SENSOR RH
DLK-125
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Component Inspection
INFOID:0000000010708081
1.
CHECK TOUCH SENSOR RH
1.
Turn ignition switch OFF.
2.
Disconnect touch sensor RH connector.
3.
Check resistance between touch sensor RH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace touch sensor RH.
Touch sensor RH
Condition
Resistance
(Approx.)
Terminal
1
2
Touch sensor RH
Detect obstruction
380 – 420 k
Ω
Other than above
0.95 – 1.05 k
Ω
DLK-126
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
B2417 TOUCH SENSOR LH
B2417 TOUCH SENSOR LH
DTC Description
INFOID:0000000010708082
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Improper installation of touch sensor
• Touch sensor LH
• Harness or connectors (touch sensor circuit is open or shorted)
• Automatic back door control unit
FAIL-SAFE
Inhibit automatic back door operation
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self Diagnostic Result” mode of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DLK-126, "Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010708083
1.
CHECK INSTALLATION OF TOUCH SENSOR LH
Check that touch sensor LH is installed normally.
Refer to
DLK-315, "TOUCH SENSOR : Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
DLK-315, "TOUCH SENSOR : Removal and Installation"
.
2.
CHECK TOUCH SENSOR MONITOR ITEM
1.
Select “AUTO BACK DOOR” using CONSULT.
2.
Select “TOUCH SEN LH” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 3.
3.
CHECK TOUCH SENSOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between touch sensor LH harness connector and automatic back door control unit harness
connector.
DTC No.
CONSULT screen items (Trou-
ble diagnosis content)
DTC detecting condition
B2417
TOUCH SEN L OPEN
(Touch sensor left open)
Automatic back door control unit detects a malfunction of touch sensor LH
during automatic operation of back door
Monitor item
Condition
Status
TOUCH SEN LH
Touch sensor LH
Other than below
OFF
Detect obstruction
ON
B2417 TOUCH SENSOR LH
DLK-127
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK TOUCH SENSOR LH CIRCUIT
1.
Disconnect automatic back door control unit and touch sensor LH connector.
2.
Check continuity between automatic back door control unit harness connector and touch sensor LH har-
ness connector.
3.
Check continuity between automatic back door control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control unit. Refer to
DLK-327, "Removal and Installation"
.
NO
>> Repair or replace harness.
5.
CHECK TOUCH SENSOR LH GROND CIRCUIT
1.
Disconnect automatic back door control unit and each touch sensor connector.
2.
Check continuity between automatic back door control unit harness connector and touch sensor LH har-
ness connector.
3.
Check continuity between automatic back door control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK TOUCH SENSOR LH
DLK-125, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace touch sensor LH.
7.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
(+)
(–)
Voltage
(Approx.)
Touch sensor LH
Connector
Terminal
D174
1
Ground
6.1 V
Automatic back door control unit
Touch sensor LH
Continuity
Connector
Terminal
Connector
Terminal
B24
2
D174
1
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B24
2
Not existed
Automatic back door control unit
Touch sensor LH
Continuity
Connector
Terminal
Connector
Terminal
B24
13
D174
2
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B24
13
Not existed
DLK-128
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
B2417 TOUCH SENSOR LH
Component Inspection
INFOID:0000000010708084
1.
CHECK TOUCH SENSOR LH
1.
Turn ignition switch OFF.
2.
Disconnect touch sensor LH connector.
3.
Check resistance between touch sensor LH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace touch sensor LH.
Touch sensor LH
Condition
Resistance
(Approx.)
Terminal
1
2
Touch sensor LH
Detect obstruction
380 – 420 k
Ω
Other than above
0.95 – 1.05 k
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст