Nissan X-Trail 32. Manual — part 1032
AIR CLEANER FILTER
EM-25
< PERIODIC MAINTENANCE >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000010783677
REMOVAL
1.
To remove air duct 2
, pinch pawl
to unlock, move pawl
frontward, and remove air duct 2 upward.
2.
Remove the clips
of air cleaner cover
.
3.
Shift air cleaner cover
to car front side and remove air cleaner
element .
INSTALLATION
Install in the reverse order of removal.
• Insert the projection
of air cleaner element
in such a way so
that it becomes the position (upper front side of car) of illustration.
• Verify that there is no looseness in air cleaner cover and has been fixed accurately.
: Vehicle front
JSBIA4626ZZ
: Vehicle front
JPBIA6829ZZ
: Projection
JPBIA6830ZZ
: Projection
JPBIA6830ZZ
EM-26
< PERIODIC MAINTENANCE >
[MR20DD]
AIR CLEANER FILTER
• Check that pawls
and
(3 in total) of air duct 2
are engaged.
Inspection (Dry Paper Type)
INFOID:0000000010783678
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• To clean air cleaner element
, blow air on it from the air intake manifold side
to remove trash or dust.
CAUTION:
• When blowing air on the air cleaner element, attach the
cover to the air cleaner case and stay away from the vehicle
as much as possible to prevent the entry of dirt into the air
cleaner case.
• Never blow air from the ambient air side to prevent clogging.
When the ambient air side needs to be cleaned, attach the
cover to the intake manifold side and lightly dust by hand.
• If clogging or damage is observed, replace the air cleaner element.
MAINTENANCE INTERVAL
: Vehicle front
JPBIA6828ZZ
Ambient air side
Air blow direction
JSBIA3460ZZ
SPARK PLUG
EM-27
< PERIODIC MAINTENANCE >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG
Exploded View
INFOID:0000000010783680
Removal and Installation
INFOID:0000000010783681
REMOVAL
1.
Remove resonater of air duct assembly. Refer to
2.
Remove ignition coil. Refer to
.
Ignition coil
Spark plug
Rocker cover
Rocker cover gasket
Oil filler cap
PCV valve
O-ring
Comply with the installation proce-
dure when tightening. Refer to
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPBIA6815GB
EM-28
< PERIODIC MAINTENANCE >
[MR20DD]
SPARK PLUG
3.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
CAUTION:
Never drop or shock spark plug.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000010783682
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
• Never drop or shock spark plug.
• Never use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Checking and adjusting plug gap is not required between
replacement intervals.
• Measure spark plug gap. when it exceeds the limit, replace
spark plug even if it is with in the specified replacement mile-
age. Refer to
.
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
: Refer to
.
Cleaner air pressure
: Less than 588 kPa (5.88 bar, 6
kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
SMA773C
JPBIA0031ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст