Nissan X-Trail 32. Manual — part 1550
LU-36
< PREPARATION >
[R9M]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010783320
Commercial Service Tools
INFOID:0000000011004695
NISSAN tool number
(RENAULT tool number)
Tool name
Description
KV113E0020
(Mot.836-05)
Oil pressure gauge set
Measuring oil pressure
JPBIA0949ZZ
Tool name
Description
Drain plug wrench
Removing and installing drain plug
: 8 mm (0.315 in)
JPBIA5904ZZ
DESCRIPTION
LU-37
< SYSTEM DESCRIPTION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SYSTEM DESCRIPTION
DESCRIPTION
Engine Lubrication System
INFOID:0000000010783321
Engine Lubrication System Schematic
INFOID:0000000010783322
E1BIA0616GB
E1BIA0617GB
LU-38
< PERIODIC MAINTENANCE >
[R9M]
ENGINE OIL
PERIODIC MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000010783323
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check that the engine oil level. If engine is already started,
stop it and allow 10 minutes before checking.
1.
Pull out oil level gauge and wipe it clean.
2.
Insert oil level gauge and check that the engine oil level is within
the range
shown in the figure.
3.
If it is out of range, adjust it.
4.
When replacing engine oil this procedure must be performed.
Refer to
EC-943, "Special Repair Requirement List"
ENGINE OIL APPEARANCE
• Check that engine oil for white turbidity or heavy contamination.
• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following area.
• Oil pan (upper and lower)
• Oil pan drain plug
• Oil pressure switch
• Oil level sensor
• Oil filter body
• Oil cooler
• Fuel pump
• Vacuum pump
• Turbocharger
• Crankshaft position sensor
• Camshaft position sensor
• Front cover
• Mating surface between cylinder head and cylinder head housing
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head housing and oil separator
• Front oil seal
• Rear oil seal retainer
OIL PRESSURE CHECK
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• When checking engine oil pressure, shift position should be “Neutral”, and apply parking brake
securely.
1.
Check engine oil level.
2.
Disconnect harness connector at oil pressure switch, and remove oil pressure switch using a deep socket.
CAUTION:
Handle oil pressure switch carefully and avoid impacts.
3.
Install oil pressure gauge set [SST:KV113E0020 (Mot.836-05)].
4.
Start engine and warm it up to normal operating temperature.
JPBIA0756ZZ
ENGINE OIL
LU-39
< PERIODIC MAINTENANCE >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
5.
Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.
If difference is extreme, check oil passage and oil pump for oil leakage.
6.
After the inspections, install oil pressure switch with the following procedure:
a.
Tighten oil pressure switch to specification.
b.
Check engine oil level.
c.
After warming up engine, check that there is no leakage of engine oil with running engine.
Draining
INFOID:0000000010783324
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
2.
Stop the engine and wait for 10 minutes.
3.
Remove engine under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
4.
Loosen oil level gauge.
5.
Remove oil pan drain plug
using a square driver [8 mm (0.315
in)]. Drain engine oil.
Refilling
INFOID:0000000010783325
1.
Install drain plug with new washer. Refer to
CAUTION:
Be sure to clean drain plug and install with new washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-23, "Fluids and Lubricants"
.
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter body for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
6.
Perform "Engine oil data reset". Refer to
.
Engine oil pressure
: Refer to
Tightening torque
: Refer to
: Vehicle front
E1BIA0601ZZ
Engine oil capacity
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст