Nissan X-Trail 32. Manual — part 935
OPERATION
EC-869
< SYSTEM DESCRIPTION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OPERATION
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : Switch Name and Function
INFOID:0000000010935580
SWITCHES AND INDICATORS
SET SPEED RANGE
ASCD system can be set the following vehicle speed.
SWITCH OPERATION
SPEED LIMITER
SPEED LIMITER : Switch Name and Function
INFOID:0000000010935581
SWITCHES AND INDICATORS
NOTE:
Shared with ASCD switch.
CRUISE indicator
CANCEL switch
ACCL/RES switch
COAST/SET switch
Speed limiter MAIN Switch
ASCD MAIN switch
On the combination meter
On the steering wheel
JSBIA5014ZZ
Minimum speed (Approx.)
Maximum speed (Approx.)
40 km/h (25 MPH)
170 km/h (105 MPH)
Item
Function
CANCEL switch
Cancels the cruise control driving.
ACCL/RES switch
• Resumes the set speed.
• Increases speed incrementally during cruise control driving.
COAST/SET switch
• Sets desired cruise speed.
• Decreases speed incrementally during cruise control driving.
ASCD MAIN switch
Master switch to activate the ASCD system.
JSBIA5018ZZ
EC-870
< SYSTEM DESCRIPTION >
[R9M]
OPERATION
SET SPEED RANGE
Speed limiter system can be set the following vehicle speed.
SWITCH OPERATION
OIL CONTROL SYSTEM
OIL CONTROL SYSTEM : Switch Name and Function
INFOID:0000000010935582
SWITCHES AND INDICATORS
SWITCH OPERATION
RESET OPERATION
CAUTION:
When an alert was displayed, change the engine oil, and reset the engine oil data.
1.
Turn ignition switch ON.
2.
On information display, select “Settings” >> “Maintenance” >> “Service”.
Speed limiter indicator
CANCEL switch
ACCL/RES switch
COAST/SET switch
Speed limiter MAIN Switch
ASCD MAIN switch
On the combination meter
On the steering wheel
Minimum speed (Approx.)
Maximum speed (Approx.)
30 km/h (20 MPH)
180 km/h (115 MPH)
Item
Function
CANCEL switch
Cancels the speed limiter control.
ACCL/RES switch
• Resumes the set speed.
• Increases the set speed incrementally.
COAST/SET switch
• Sets desired speed.
• Decreases the set speed incrementally.
Speed limiter MAIN switch
Master switch to activate the speed limiter system.
Combination meter
Steering
Information display
Enter/Up/Down switch
Back switch
Display switch
JSBIA5023ZZ
Item
Function
Steering switch
OPERATION
EC-871
< SYSTEM DESCRIPTION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3.
Press “ENTER” switch until “YES/NO” is appeared.
4.
Select “YES”.
5.
Check that “– – –” is displayed.
STOP/START SYSTEM
STOP/START SYSTEM : Switch Name and Function
INFOID:0000000010935583
SWITCHES AND INDICATORS
SWITCH OPERATION
NOTE:
If stop/start OFF switch turn ON when stop/start system is operating, stop/start system is canceled and engine
restart.
Stop/start indicator lamp
Stop/start OFF switch
On the combination meter
Lower instrument panel (driver side)
JSBIA3803ZZ
Item
Function
Stop/start OFF switch
When the switch is pressed, switch indicator (LED) turns ON and the stop/start
system can be deactivated.
EC-872
< SYSTEM DESCRIPTION >
[R9M]
HANDLING PRECAUTION
HANDLING PRECAUTION
Precaution for Stop/Start System
INFOID:0000000010935584
PRECAUTIONS FOR STOP/START SYSTEM OPERATION
The operation of the stop/start system needs to satisfy various conditions. For details of the conditions, refer to
EC-848, "STOP/START SYSTEM : System Description (M/T models)"
SYSTEM : System Description (CVT models)"
(CVT models).
The stop/start system may not operate under the conditions listed below:
• After restarting the engine, the vehicle is repeatedly stopped and started at a low speed due to traffic con-
gestion.
• When driving the vehicle repeatedly back and forth at a low speed due to parallel parking.
• When the intelligent key is not authenticated. (In this case, the KEY warning lamp built in the combination
meter blinks.)
• The battery is deteriorated. (High discharge rate.)
• A battery other than the stop/start system-specific battery is used.
• Ambient temperature is extremely low.
HANDLING PRECAUTIONS
• When engine restart conditions are satisfied during the electric parking brake operation, ECM performs the
engine restart after the completion of the electric parking brake operation. This may cause delay in engine
restart, compared with a usual engine restart.
For a smooth engine restart under the stop/start system operating condition, restart the engine before
releasing the parking brake.
• To use the stop/start system, the vehicle needs to recognize the status of battery. For this reason, the stop/
start system may not be activated immediately after battery change.
• (For M/T only) When restarting the vehicle under stop/start system operating condition, continue depressing
the clutch pedal until the restart completes.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст