Nissan X-Trail 32. Manual — part 1265

FAX-52

< REMOVAL AND INSTALLATION >

[2WD]

FRONT DRIVE SHAFT

11. Remove drive shaft from wheel hub and bearing assembly.

CAUTION:

• Never place drive shaft joint at an extreme angle.
• Be careful not to overextend slide joint.

12. Remove drive shaft from transaxle assembly.

• Use the drive shaft attachment (A) (SST: KV40107500) and a

sliding hammer (B) (commercial service tool) while inserting
tip of the drive shaft attachment between housing and tran-
saxle assembly.

CAUTION:

• Never place drive shaft joint at an extreme angle when

removing drive shaft. Also be careful not to overextend
slide joint.

• Confirm that the circular clip is attached to the drive

shaft.

Right Side

1.

Remove tires. Refer to

WT-61, "Removal and Installation"

.

2.

Remove wheel sensor from steering knuckle. Refer to

BRC-212, "FRONT WHEEL SENSOR : Removal

and Installation"

.

3.

Remove lock plate

from strut assembly.

• LHD: Refer to

BR-24, "FRONT : Exploded View"

.

• RHD: Refer to

BR-88, "FRONT : Exploded View"

.

4.

Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD (1 PISTON TYPE): Refer to

BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal

and Installation"

.

• LHD (2 PISTON TYPE): Refer to

BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal

and Installation"

.

• RHD (1 PISTON TYPE): Refer to

BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal

and Installation"

.

• RHD (2 PISTON TYPE): Refer to

BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal

and Installation"

.

CAUTION:

Never depress brake pedal while brake caliper is removed.

5.

Remove disc rotor. Refer to

FAX-11, "Removal and Installation"

.

JSDIA5562ZZ

JPDIF0004ZZ

JSDIA3795ZZ

FRONT DRIVE SHAFT

FAX-53

< REMOVAL AND INSTALLATION >

[2WD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

6.

Remove cotter pin, adjusting cap and then loosen wheel hub
lock nut, using a hub lock nut wrench (A) (SST: KV40104000).

7.

Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub and bearing assembly from drive
shaft.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.

8.

Remove wheel hub lock nut.

9.

Remove transverse link from steering knuckle and front suspension member. Refer to

FSU-17, "Removal

and Installation"

.

10. Separate steering outer socket from steering knuckle. Refer to

ST-22, "Removal and Installation"

.

11. Remove drive shaft from wheel hub and bearing assembly.

CAUTION:

• Never place drive shaft joint at an extreme angle.
• Be careful not to overextend slide joint.

12. Remove retainer mounting bolts and retainer.
13. Remove drive shaft from transaxle assembly.

• Use the drive shaft attachment (SST: KV40107500) and a sliding hammer while inserting tip of the drive

shaft attachment between housing and transaxle assembly.

CAUTION:

Never place drive shaft joint at an extreme angle when removing drive shaft. Also be careful not
to overextend slide joint.

14. If necessary, remove the support bearing bracket mounting bolts, support bearing bracket and the heat

insulator.

INSTALLATION

Left Side

Note the following, and install in the reverse order of removal.

CAUTION:

Always replace differential side oil seal with new one when installing drive shaft.
• M/T: Refer to

TM-118, "Removal and Installation"

.

• CVT: Refer to

TM-690, "Removal and Installation"

.

JSDIA2708ZZ

JPDIG0070ZZ

JSDIA5562ZZ

FAX-54

< REMOVAL AND INSTALLATION >

[2WD]

FRONT DRIVE SHAFT

• Place the protector (A) (SST: KV38107900) onto transaxle assem-

bly to prevent damage to the differential side oil seal while inserting
drive shaft. Slide drive shaft sliding joint and tap with a hammer to
install securely.

CAUTION:

• Check that circular clip is completely engaged.
• Never reuse differential side oil seal.

• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.

CAUTION:

Never apply lubricating oil to these matching surface.

• Clean the matching surface of drive shaft and wheel hub and bear-

ing assembly. And then apply paste [service parts (440037S000)]
to surface

of joint sub-assembly of drive shaft.

CAUTION:

Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.

• Tighten the wheel hub lock nut to the specified torque. Refer to

FAX-11, "Exploded View"

.

CAUTION:

• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel

hub lock nut.

• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.

• When installing a cotter pin

and adjusting cap

, securely bend

the basal portion to prevent rattles.

CAUTION:

Never reuse cotter pin.

• Perform inspection after installation. Refer to

FAX-60, "R9M : Inspection"

.

Right Side

Note the following, and install in the reverse order of removal.

CAUTION:

Always replace differential side oil seal with new one when installing drive shaft.
• M/T: Refer to

TM-118, "Removal and Installation"

.

• CVT: Refer to

TM-690, "Removal and Installation"

.

JPDIF0023ZZ

Amount paste

: 1.0 – 3.0 g (0.04 – 0.10 oz)

JPDIG0122ZZ

JPDIF0295ZZ

FRONT DRIVE SHAFT

FAX-55

< REMOVAL AND INSTALLATION >

[2WD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

• Place the protector (A) (SST: KV38107900) onto transaxle assem-

bly to prevent damage to the differential side oil seal while inserting
drive shaft. Slide drive shaft sliding joint and tap with a hammer to
install securely.

-

CAUTION:

Never reuse differential side oil seal.

• When installing support bearing bracket tighten the mounting bolt with the following procedure.
- To install support bearing bracket

and mounting bolts, tempo-

rarily tighten the bolts before tightening to the specified torque,
referring to the tightening method and the numerical order shown
below:

- Set plate

so thet the notch part

becomes upper side.

CAUTION:

Never reuse plate.

- Temporarily tighten the bolts before tightening to the specified

torque, referring to the tightening method and the numerical order
shown below:

• Instal the heat insulator

to touch a projection

of the bracket

as shown in figure.

• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.

CAUTION:

Never apply lubricating oil to these matching surface.

• Clean the matching surface of drive shaft and wheel hub and bear-

ing assembly. And then apply paste [service parts (440037S000)]
to surface

of joint sub-assembly of drive shaft.

CAUTION:

Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.

JSDIA6354ZZ

Temporary tightening

: 1

→

2

Final tightening (Specified torque)

: 3

→

4

Temporary tightening

: 5

→

6

Final tightening (Specified torque)

: 7

→

8

JSDIA6126ZZ

JSDIA6124ZZ

Amount paste

: 1.0 – 3.0 g (0.04 – 0.10 oz)

JPDIG0122ZZ