Nissan X-Trail 32. Manual — part 1379
CONDENSER
HA-175
< REMOVAL AND INSTALLATION >
[R9M (FOR RUSSIA)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER
Exploded View
INFOID:0000000011007759
CONDENSER
CONDENSER : Removal and Installation
INFOID:0000000011007760
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
159, "Perform Lubricant Return Operation"
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2.
Remove front bumper fascia assembly. Refer to
EXT-15, "Removal and Installation"
.
3.
Remove mounting bolt
, and then disconnect high-pressure
pipe 1 from the condenser & liquid tank assembly.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with
suitable material such as vinyl tape to avoid the entry of air.
1.
Condenser & liquid tank assembly
2.
Radiator
: Pawl
JMIIA3533ZZ
JMIIA3743ZZ
HA-176
< REMOVAL AND INSTALLATION >
[R9M (FOR RUSSIA)]
CONDENSER
4.
Remove mounting bolt
, and then disconnect high-pressure
pipe 2 from the condenser & liquid tank assembly.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with
suitable material such as vinyl tape to avoid the entry of air.
5.
Disengage fixing pawls, and then remove the condenser from
the vehicle according to numerical order 1
→
2 indicated by
arrows as shown in the figure.
CAUTION:
Never damage core surface of condenser.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Perform lubricant adjusting procedure before installing new condenser. Refer to
Adjusting Procedure for Components Replacement Except Compressor"
• Check for leakages when recharging refrigerant. Refer to
.
JMIIA3742ZZ
: Pawl
JMIIA3744ZZ
A/C UNIT ASSEMBLY
HA-177
< REMOVAL AND INSTALLATION >
[R9M (FOR RUSSIA)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
A/C UNIT ASSEMBLY
Exploded View
INFOID:0000000011007761
REMOVAL
DISASSEMBLY
1.
Cap
2.
Steering member
3.
Instrument stay LH
4.
Instrument stay RH
5.
A/C unit assembly
6.
Drain hose
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMIIA3519GB
HA-178
< REMOVAL AND INSTALLATION >
[R9M (FOR RUSSIA)]
A/C UNIT ASSEMBLY
A/C UNIT ASSEMBLY
A/C unit case RH
Blower motor assembly
Filter cover RH
Sub harness
PTC heater
O-ring
Expansion valve
Main case center
Sub harness
Cooler packing
Heater pipe packing
Intake packing
Heater pipe clamp
Air conditioner filter
Evaporator assembly
Case packing
A/C unit case LH
Heater core
A/C auto amp.
(automatic air conditioning)
Filter cover LH
Intake sensor
Intake box case lower
Heater pipe cover
Aspirator
(automatic air conditioning)
Aspirator duct
(automatic air conditioning)
Intake door
Power transistor
(automatic air conditioning)
Fan control amplifier
(manual air conditioning)
Intake box case upper
Foot door
Plate case center
Air mix door RH
Air mix door LH
Center ventilator door·center ventila-
tor & defroster door rod
Foot door & mode door rod
Side ventilator door
Main case rear
Mode door
Center ventilator & defroster door
Air guide case
Side ventilator packing LH
Center ventilator packing
Side ventilator packing RH
Defroster packing
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JMIIA3520GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст