Nissan X-Trail 32. Manual — part 1187
REAR COMBINATION LAMP
EXL-205
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP (BACK DOOR SIDE) : Removal and Installation
INFOID:0000000010788900
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-9, "Precautions for Removing Battery Terminal"
.
REMOVAL
1.
Fully open back door.
2.
Remove back door inner finisher. Refer to
INT-47, "Removal and Installation"
3.
Disconnect rear combination lamp (back door side) harness
connector .
4.
Remove rear combination lamp (back door side) mounting nuts
.
5.
Apply protective tape (A) on the part to protect it from damage.
6.
Disengage rear combination lamp (back door side) fixing clips
using a remover tool (A), and then remove rear combination
lamp (back door side).
INSTALLATION
JMLIA4970ZZ
JMLIA4971ZZ
JMLIA4972ZZ
: Clip
JMLIA4973ZZ
EXL-206
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
Install in the reverse order of removal.
REAR COMBINATION LAMP (BACK DOOR SIDE) : Replacement
INFOID:0000000010788901
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-9, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
TAIL LAMP BULB
1.
Remove rear combination lamp (back door side). Refer to
EXL-205, "REAR COMBINATION LAMP
(BACK DOOR SIDE) : Removal and Installation"
.
2.
Rotate tail lamp bulb socket counterclockwise, and then remove tail lamp bulb socket.
3.
Remove tail lamp bulb from tail lamp bulb socket.
BACK-UP LAMP BULB
1.
Remove rear combination lamp (back door side). Refer to
EXL-205, "REAR COMBINATION LAMP
(BACK DOOR SIDE) : Removal and Installation"
.
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
HIGH-MOUNTED STOP LAMP
EXL-207
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000010788902
Removal and Installation
INFOID:0000000010788903
CAUTION:
Disconnect battery negative terminal or remove power circuit fuse when performing the operation for
preventing electric leakage. Refer to
EXL-9, "Precautions for Removing Battery Terminal"
REMOVAL
1.
Fully open back door.
2.
Apply protective tapes (A) on the part to protect it from damage.
High-mounted stop lamp
: N·m (kg-m, in-lb)
JMLIA4963GB
JMLIA4974ZZ
EXL-208
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
HIGH-MOUNTED STOP LAMP
3.
Disengage back door cover fixing metal clips and pawls using a
remover tool (A), and then remove back door cover.
4.
Remove high-mounted stop lamp mounting nuts
.
5.
Disconnect high-mounted stop lamp harness connector
, and
then remove high-mounted stop lamp.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010788904
CAUTION:
Disconnect battery negative terminal or remove power circuit fuse when performing the operation for
preventing electric leakage. Refer to
EXL-9, "Precautions for Removing Battery Terminal"
HIGH-MOUNTED STOP LAMP BULB
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
high-mounted stop lamp unit as a set. Refer to
EXL-207, "Removal and Installation"
.
: Pawl
: Metal clip
JMLIA4975ZZ
JMLIA4976ZZ
JMLIA4977ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст