Nissan X-Trail 32. Manual — part 639
REAR DOOR
DLK-897
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Front fender
Front door
Rear door
Body side outer
Door striker
TORX bolt
Front door hinge
Rear door hinge (upper)
Rear door hinge (lower)
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3479GB
DLK-898
< REMOVAL AND INSTALLATION >
[TYPE 4]
REAR DOOR
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal
2.
Loosen door hinge mounting nuts of door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts of door side.
5.
Loosen door hinge mounting nuts and bolts of vehicle body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment, tighten bolts and nuts to the specified torque.
CAUTION:
After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts and
nuts.
8.
Install center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal and
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010728646
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• After installation, perform the fitting adjustment. Refer to
DLK-896, "DOOR ASSEMBLY : Adjust-
• After installation, check that door opens and closes normally. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010728647
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door assembly. Refer to
DLK-895, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal
Portion
Standard
Front door – Rear door
–
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Rear door – Body side outer
–
L
Clearance
3.0 – 5.0
[0.118 – 0.197]
M
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
REAR DOOR
DLK-899
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove rear door hinge mounting bolts and nuts of vehicle body side, and then remove rear door hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-896, "DOOR ASSEMBLY : Adjust-
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting bolts
and nuts.
• After installation, check that door opens and closes normally. Refer to
.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010728648
REMOVAL
1.
Fully close rear door glass.
2.
Remove rear door finisher. Refer to
INT-19, "Removal and Installation"
.
3.
Disconnect harness connector of rear door speaker.
4.
Remove mounting bolts of rear door speaker, and then remove rear door speaker.
5.
Remove door check link mounting bolt of vehicle body side.
6.
Remove door check link mounting bolts of door panel, and then
take door check link
out from the hole of door panel
.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check that door opens and closes normally. Refer to
.
DOOR WEATHER-STRIP
DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000010728649
REMOVAL
1.
Apply protective tape (A) to rear door panel
around rear door
weather-strip
fixing clips for preventing damage.
JMKIB3512ZZ
JMKIB0410ZZ
DLK-900
< REMOVAL AND INSTALLATION >
[TYPE 4]
REAR DOOR
2.
Disengage fixing clips on the reverse side of rear door weather-
strip using a remover tool (A).
CAUTION:
• Never damage rear door panel.
• When removing, never confuse the 3 types of rear door weather-strip
fixing clips
,
and
.
3.
Remove front fixing clips from weather-strip.
: Clip
JMKIB0411ZZ
: Vehicle front
JMKIB3513ZZ
JMKIB3514ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст