Nissan X-Trail 32. Manual — part 1274
FAX-88
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT BOOT
11. Remove drive shaft from wheel hub and bearing assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle.
• Be careful not to overextend slide joint.
12. Remove boot bands, and then separate boot from joint sub-assembly.
13. Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• Align sliding hammer and drive shaft and remove them by
pulling directory.
• If joint sub-assembly cannot be pulled out, try after
removing drive shaft from vehicle. Refer to
"QR25DE : Disassembly and Assembly"
.
14. Remove circular clip
from shaft.
15. Remove boot from shaft.
Transaxle Side
Remove boot after removing drive shaft.
• Remove: Refer to
FAX-113, "QR25DE : Removal and Installation"
• Disassembly: Refer to
FAX-119, "QR25DE : Disassembly and Assembly"
INSTALLATION
Wheel Side
1.
Clean the old grease on joint sub-assembly with paper waste.
2.
Fill serration slot joint sub-assembly
with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a shop cloth to wipe off old
grease that has oozed out.
JSDIA5562ZZ
JPDIF0258ZZ
JPDIF0007ZZ
JPDIF0008ZZ
FRONT DRIVE SHAFT BOOT
FAX-89
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
3.
Install boot and boot bands to shaft.
CAUTION:
• Never reuse boot and boot band.
• Wrap serration on shaft with tape
to protect the boot
from damage.
4.
Remove the tape wrapped around the serration on shaft.
5.
Position the circular clip
on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip
.
6.
Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with joint sub-
assembly holding circular clip.
7.
Install joint sub-assembly
to shaft using plastic hammer.
CAUTION:
• Check circular clip is properly positioned on groove of the
joint sub-assembly.
• Confirm that joint sub-assembly is correctly engaged
while rotating drive shaft.
8.
Fill into the boot inside with the specified amount of grease from large diameter side of boot.
JPDIF0009ZZ
JPDIF0007ZZ
JPDIF0010ZZ
JPDIF0011ZZ
Grease amount
: Refer to
.
FAX-90
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT BOOT
9.
Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on the shaft or joint subassembly. boot may be
removed. Remove all grease from the boot mounting sur-
face.
10. To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into the inside of the boot from the large diame-
ter side of the boot and discharging the inside air.
CAUTION:
• If the boot mounting length exceeds the standard, it may cause breakage in the boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) (SST: KV40107300).
CAUTION:
Never reuse boot band.
NOTE:
Secure boot band so that dimension (M) meets the specification as shown in the figure.
12. Check that displacement does not occur when boot is rotated with the joint sub-assembly and shaft fixed.
CAUTION:
• Reinstall them using boot bands when boot installation positions become incorrect.
• Never reuse boot band.
13. Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
L
: Refer to
.
JPDIG0136ZZ
JPDIF0012ZZ
M
: 1.0 – 4.0 mm (0.039 – 0.157 in)
DSF0047D
FRONT DRIVE SHAFT BOOT
FAX-91
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
14. Clean the matching surface of drive shaft and wheel hub and
bearing assembly. And then apply paste [service parts
(440037S000)] to surface
of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assem-
bly of drive shaft.
15. Insert drive shaft to wheel hub and bearing assembly, and then temporarily tighten wheel hub lock nut.
CAUTION:
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
16. Install transverse link to steering knuckle and front suspention member. Refer to
.
17. Install steering outer socket to steering knuckle.
• LHD: Refer to
• RHD: Refer to
.
18. Tighten the wheel hub lock nut to the specified torque. Refer to
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
19. When installing a cotter pin
and adjusting cap
, securely
bend the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
20. Install disc rotor. Refer to
FAX-72, "Removal and Installation"
21. Install caliper assembly to steering knuckle.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
22. Install lock plate to strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
23. Install wheel sensor to steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal and
.
24. Install tires to vehicle.Refer to
WT-61, "Removal and Installation"
25. Perform inspection after installation. Refer to
.
Transaxle Side
• Installation: Refer to
FAX-113, "QR25DE : Removal and Installation"
.
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JPDIG0122ZZ
JPDIF0295ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст