Nissan X-Trail 32. Manual — part 2153

TM-570

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0705 TRANSMISSION RANGE SENSOR A

3.

CHECK D POSITION SW CIRCUIT (PART 2)

1.

Disconnect transmission range switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK N POSITION SW CIRCUIT (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK N POSITION SW CIRCUIT (PART 2)

1.

Disconnect transmission range switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK P POSITION SW CIRCUIT (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM harness connector terminals.

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F119

4

Ground

0 V

TCM

Continuity

Connector

Terminal

F119

5

2

Not existed

4

6

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F119

5

Ground

0 V

P0705 TRANSMISSION RANGE SENSOR A

TM-571

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK P POSITION SW CIRCUIT (PART 2)

1.

Disconnect transmission range switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

8.

CHECK R POSITION SW CIRCUIT (PART1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace malfunctioning parts.

9.

CHECK R POSITION SW CIRCUIT (PART 2)

1.

Disconnect transmission range switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

TCM

Continuity

Connector

Terminal

F119

7

2

Not existed

4

5

6

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F119

7

Ground

0 V

TCM

Continuity

Connector

Terminal

F119

6

2

Not existed

4

5

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F119

6

Ground

0 V

TM-572

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0705 TRANSMISSION RANGE SENSOR A

10.

CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to

TM-572, "Component Inspection"

.

Is the check result normal?

YES

>> INSPECTION END

NO

>> Repair or replace malfunctioning parts.

Component Inspection

INFOID:0000000010622795

1.

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to

TM-

681, "Removal and Installation"

.

Transmission range switch

Condition

Continuity

Terminal

1 – 2

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

3 – 4

Manual lever: “P” position

Existed

Other than the above

Not existed

3 – 5

Manual lever: “R” position

Existed

Other than the above

Not existed

3 – 6

Manual lever: “N position

Existed

Other than the above

Not existed

3 – 7

Manual lever: “D” position

Existed

Other than the above

Not existed

P0706 TRANSMISSION RANGE SENSOR A

TM-573

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0706 TRANSMISSION RANGE SENSOR A

DTC Description

INFOID:0000000010622796

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit

between transmission range switch and TCM)

• Transmission range switch
• Control cable
Harness or connector (CAN communication line is error)

FAIL-SAFE

• Shift position indicator on combination meter is not displayed
• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
40 seconds or more.)

3.

Check the first trip DTC.

Is “P0706” detected?

YES

>> Go to

TM-573, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010622797

1.

ADJUSTMENT OF CONTROL CABLE

Adjust control cable. Refer to

TM-308, "Adjustment"

.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Select “Self Diagnostic Results” in “TRANSMISSION”.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0706

T/M RANGE SENSOR A
(Transmission Range Sensor A Circuit Range/
Performance)

When all of the following conditions are satisfied and this state is main-
tained for 30 seconds:
• All range signals stay OFF
• TCM power supply voltage: More than 11 V