Nissan X-Trail 32. Manual — part 504
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-357
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Operation Description
• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal is transmitted
from Intelligent Key to BCM via remote keyless entry receiver.
• BCM receives the signal and compares it with the registered key ID to the vehicle.
• BCM lock/unlock each door lock actuator, when key ID matches.
Operation Condition
If the following condition is satisfied, door lock and unlock operation is performed if the Intelligent Key button is
pressed.
ANTI-HIJACK FUNCTION
• When an LOCK signal is transmitted from Intelligent Key, all doors are locked.
• When an UNLOCK signal is transmitted from Intelligent Key once, driver door is unlocked.
• Then, if an UNLOCK signal is transmitted from Intelligent Key again, all other doors are unlocked.
How to change anti-hijack mode.
With CONSULT
Anti-hijack mode can be set to ON or OFF using CONSULT.
Refer to
DLK-384, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (With Intelligent Key System,
Without CONSULT
Anti-hijack function can be set to ON/OFF by user with a registered Intelligent Keyfob.
• ON/OFF can be switched when Intelligent Key lock button and unlock button are pressed simultaneously for
5 seconds or more while steering lock is locked.
• When mode is switched, hazard warning lamp blinks.
REMINDER FUNCTION (INTELLIGENT KEY)
Operation Description
When doors are locked or unlocked by Intelligent Key button operation, BCM blinks hazard warning lamps as
a reminder.
AUTO DOOR LOCK FUNCTION (INTELLIGENT KEY)
After door is unlocked by Intelligent Key button operation and if 30 seconds or more passes without performing
the following operation, all doors are automatically locked. However, operation check function does not acti-
vate.
How to Change Auto Door Lock Function Operation Time
Auto door lock function operation time can be changed using CONSULT.
Refer to
DLK-385, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Without Super
.
Intelligent Key button opera-
tion
Operation condition
Lock
• Ignition switch: OFF position
• P position warning is not activated
• All doors are closed
Unlock
Ignition switch: OFF position
OFF
→
ON
: 1 blink
ON
→
OFF
: 3 blinks
Door lock operation
(With Intelligent Key button)
Hazard warning lamp blink
Lock
Once
Unlock (all door unlock)
Twice
Unlock (anti-hijack operation)
Twice (quick)
Operating condition
• Door switch is ON (door is open)
• BCM receives lock signal
• Push switch is pressed
DLK-358
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (INTELLIGENT KEY SYSTEM)
AUTOMATIC BACK DOOR OPEN/CLOSE FUNCTION
When back door open button is pressed, back door open automatically for detailed description.
Refer to
OPERATION AREA
To check that the Intelligent Key works normally, use within 1 m (3 ft.) range of each door, however the opera-
ble range may differ according to surroundings.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
KEY REMINDER FUNCTION
KEY REMINDER FUNCTION : System Description
INFOID:0000000010717442
SYSTEM DIAGRAM
BASIC OPERATION
Key reminder is the function that prevents the key from being left in the vehicle.
Key reminder has the following 3 functions.
Function
In
tel
lig
en
t K
e
y
Re
mo
te
ke
yl
es
s en
try rec
e
iv
e
r
Do
or swi
tch
Do
or l
o
ck
ac
tu
at
o
r
Pu
sh
-bu
tto
n i
g
n
iti
on
swi
tch
CAN communication
system
BCM
IPDM
E/
R
Au
tom
a
ti
c
ba
ck
d
o
o
r co
nt
rol
un
it
Combination meter
Hazard warning
lamp
Door lock and unlock function (Intelligent Key)
×
×
×
×
×
Reminder function (Intelligent Key)
×
×
×
×
×
×
×
×
Auto door lock function (Intelligent Key)
×
×
×
×
×
×
Automatic back door open/close function
×
×
×
×
×
JMKIB3556GB
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-359
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*:If the door closing impact shocks the door lock knob, or contacts against baggage with the door lock knob might activate the door locks
accidentally but unlock operation is perform in these cases.
NOTE:
The above function operates when the Intelligent Key is inside the vehicle. However, there may be times when
the Intelligent Key cannot be detected, and this function does not operate when the Intelligent Key is on the
instrument panel, rear parcel shelf, or in the glove box. Also, this system sometimes does not operate if the
Intelligent Key is in the door pocket for the open door.
INFORMATION DISPLAY (COMBINATION METER)
INFORMATION DISPLAY (COMBINATION METER) : Door Open Warning
INFOID:0000000010750521
DESIGN/PURPOSE
Information display warns the driver that each door is open or is not fully closed.
SYNCHRONIZATION WITH MASTER WARNING LAMP
Synchronization is applied.
Refer to
MWI-47, "WARNING LAMPS/INDICATOR LAMPS : Master Warning Lamp"
SYSTEM DIAGRAM
SIGNAL PATH
• BCM transmits door switch signal to combination meter via CAN communication.
Key remainder function
Operation condition
Operation
Driver door opened
Right after door is locked by door lock/unlock switch or driver door lock
knob operation under the following conditions
• Ignition switch: LOCK or OFF position
• Registered Intelligent Key is inside the vehicle
• Driver door is opened
All doors unlock
Driver door closed
*
When all doors are locked by door lock/unlock switch or driver door lock
knob within 0.2 seconds after driver door is closed
All doors unlock
Door is open to closed
When all of the following conditions are satisfied
• Locked all doors
• [Any door: open]
→
[all doors: closed]
• Registered Intelligent Key is inside the vehicle
• All doors unlock
• Honk Intelligent Key warn-
ing buzzer
Symbol
Message
–
JMKIB2780ZZ
JMKIB3593GB
DLK-360
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (INTELLIGENT KEY SYSTEM)
• When combination meter judges according to received door switch signal that a door is open or not fully
closed, door open warning displays.
WARNING/INDICATOR OPERATIONG CONDITION
Each door switch is ON
WARNING/INDICATOR CANCEL CONDITION
All door switches are OFF
TIMING CHART
INFORMATION DISPLAY (COMBINATION METER) : Engine Start Information
INFOID:0000000010750522
DESIGN/PURPOSE
Information display informs the driver that the engine can be started.
SYNCHRONIZATION WITH MASTER WARNING LAMP
No applicable
JMKIB3594GB
Symbol
Message
CVT models
–
M/T models
–
JMKIB1883ZZ
JMKIB1884ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст