Nissan X-Trail 32. Manual — part 2088
TM-310
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
U0073 COMMUNICATION BUS A OFF
DTC/CIRCUIT DIAGNOSIS
U0073 COMMUNICATION BUS A OFF
DTC Description
INFOID:0000000010622488
DTC DETECTION LOGIC
POSSIBLE CAUSE
Harness or connector (CAN communication line is error)
FAIL-SAFE
• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine and wait for at least 5 seconds.
2.
Check the DTC.
Is “U0073” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622489
For the diagnosis procedure, refer to
LAN-17, "Trouble Diagnosis Flow Chart"
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
U0073
COMM BUS A OFF
(Control Module Communication Bus A Off)
TCM communication blockage lasts for 2 seconds or more when turning
ON the ignition switch. (Communication not established.)
U0100 LOST COMMUNICATION (ECM A)
TM-311
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
U0100 LOST COMMUNICATION (ECM A)
DTC Description
INFOID:0000000010622490
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ECM
• Harness or connector (CAN communication line is open or shorted)
FAIL-SAFE
• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine and wait for at least 5 seconds.
2.
Check the DTC.
Is “U0100” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622491
For the diagnosis procedure, refer to
LAN-17, "Trouble Diagnosis Flow Chart"
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
U0100
LOST COMM (ECM A)
(Lost Communication With ECM/PCM A)
When the ignition switch is ON, TCM is unable to receive the CAN
communications signal from ECM continuously for 2 seconds or more.
TM-312
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
U0102 LOST COMMUNICATION (TRANSFER)
U0102 LOST COMMUNICATION (TRANSFER)
DTC Description
INFOID:0000000010622492
DTC DETECTION LOGIC
POSSIBLE CAUSE
• AWD control unit
• Harness or connector (CAN communication line is open or shorted)
FAIL-SAFE
Not changed from normal driving
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Start the engine and wait for at least 5 seconds.
2.
Check the DTC.
Is “U0102” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622493
For the diagnosis procedure, refer to
LAN-17, "Trouble Diagnosis Flow Chart"
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
U0102
LOST COMM (TRANSFER)
(Lost Communication With Transfer Case Con-
trol Module)
When the ignition switch is ON, TCM is unable to receive the CAN com-
munications signal from AWD control unit continuously for 2 seconds or
more.
U0140 LOST COMMUNICATION (BCM)
TM-313
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
U0140 LOST COMMUNICATION (BCM)
DTC Description
INFOID:0000000010622494
DTC DETECTION LOGIC
POSSIBLE CAUSE
• BCM
• Harness or connector (CAN communication line is open or shorted)
FAIL-SAFE
Not changed from normal driving
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Start the engine and wait for at least 5 seconds.
2.
Check the DTC.
Is “U0140” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622495
For the diagnosis procedure, refer to
LAN-17, "Trouble Diagnosis Flow Chart"
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
U0140
LOST COMM (BCM)
(Lost Communication With Body Control Mod-
ule)
When the ignition switch is ON, TCM is unable to receive the CAN com-
munications signal from BCM continuously for 2 seconds or more.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст