Nissan X-Trail 32. Manual — part 622
KEYFOB ID REGISTRATION
DLK-829
< BASIC INSPECTION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID REGISTRATION
Description
INFOID:0000000010755026
Perform the system initialization when replacing BCM, replacing keyfob or registering an additional keyfob.
Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.
DLK-830
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
BACK DOOR SWITCH
DTC/CIRCUIT DIAGNOSIS
BACK DOOR SWITCH
Component Function Check
INFOID:0000000010755027
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “DOOR LOCK” of “BCM” using CONSULT.
3.
Select “DOOR SW-BK” in “DATA MONITOR” mode.
4.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Back door switch is OK.
NO
>> Refer to
DLK-830, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010755028
1.
CHECK BACK DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door lock assembly connector.
3.
Check signal between back door lock assembly harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between back door lock assembly harness connector and BCM harness connector.
3.
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR SWITCH GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Monitor item
Condition
Status
DOOR SW-BK
Back door
Open
On
Closed
Off
(+)
(–)
Voltage
Back door lock assembly
Connector
Terminal
D168
3
Ground
9 – 16 V
Back door lock assembly
BCM
Continuity
Connector
Terminal
Connector
Terminal
D168
3
B47
11
Existed
Back door lock assembly
Ground
Continuity
Connector
Terminal
D168
3
Not existed
BACK DOOR SWITCH
DLK-831
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR SWITCH
DLK-831, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door lock assembly.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010755029
1.
CHECK BACK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door lock assembly connector.
3.
Check continuity between back door lock assembly terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door lock assembly.
Back door lock assembly
Ground
Continuity
Connector
Terminal
D168
4
Existed
Back door lock assembly
Condition
Continuity
Terminal
3
4
Back door lock
Lock
Existed
Unlock
Not existed
DLK-832
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
BACK DOOR OPENER ACTUATOR
BACK DOOR OPENER ACTUATOR
Diagnosis Procedure
INFOID:0000000010755030
1.
CHECK BACK DOOR OPENER ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door lock assembly connector.
3.
Check voltage between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR OPENER ACTUATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door lock assembly harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR OPENER ACTUATOR GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection normal?
YES
>> Replace back door lock assembly.
NO
>> Repair or replace harness.
(+)
(–)
Condition
Voltage
Back door lock assembly
Connector
Terminal
D168
1
Ground
Back door
opener switch
ON
9 – 16 V
BCM
Back door lock assembly
Continuity
Connector
Terminal
Connector
Terminal
B46
121
D168
1
Existed
BCM
Ground
Continuity
Connector
Terminal
B46
121
Not existed
Back door lock assembly
Ground
Continuity
Connector
Terminal
D168
2
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст